Question about 1991 Dodge Spirit

Open Question

1991 dodge spirit round inner tie rod.

What inner tie rod adapter size do I need to change the inner tie rod of a 1991 dodge spirit. I used a saginaw it did not stay on the tie rod at all. it kept slipping off.

Posted by on

5 Suggested Answers

justuscc
  • 360 Answers

SOURCE: replacing outer tie rod on a 2000 dodge neon

put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Posted on Oct 03, 2008

  • 1 Answer

SOURCE: Inner tie rod 99 durango replacement

make sure if you do it youself you count how many turns it takes for your tierods to come off. it it makes it easy for me that way. also make sure you get a front end aligiment when your done

Posted on Dec 07, 2008

  • 1596 Answers

SOURCE: 1997 dodge Intrepid: inner tie rod

To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
NUMBER: 19-001-01
GROUP: Steering
DATE: Mar. 23, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

SUBJECT:
Loose Steering

OVERVIEW:
This bulletin provides service procedures and parts information for the inner tie rod bushings.
MODELS:
1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
SYMPTOM/CONDITION:
Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
DIAGNOSIS:
Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
DISCUSSION:
The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

Posted on Jan 13, 2009

  • 750 Answers

SOURCE: Loose inner tie rods on '97 Dodge Dakota Sport 2WD

corect size wrench should work. count the number of turn it takes to remove each unit make note and install new units using those numbers

Posted on Jun 29, 2009

johnjohn2
  • 5763 Answers

SOURCE: how to replace inner tie rod on 99 dodge durango

disconnect from outter tie rod. unclamp boot slide forward. unscrew inner tierod off rack. good luck.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My durango had a tie rod break on the front drivers side. I took the piece to the auto parts store and they need to know if it is an inner or outer and the size is either 15mm or 16mm. I do not know how to...


It may be stuck on defrost cycle due to a bad timer... is there an adjustable switch that you could adjust it should start up... let me know......

Jul 20, 2011 | 2005 Dodge Durango

2 Answers

Need to replace inner tie rod on a 1998 ford ranger two wheel drive , driver side . engine size is 2.5. do i have to take outer tie rod off as well?


webbraymond2, Yes, you have to remove the outer tie to access the inner tie rod. When you do this, count the rotations of the tie rod as this will have to be replaced when the new inner tie rod is installed. Counting the rotations will allow you to put the outer tie rod close to where it was when you started the job. You are changing the toe setting when you have to replace either the inner or outer tie rod. You need to access and remove the jamb nut and boot before you can access the inner tie rod and this is why the outer needs to be removed first. A wheel alignment is advised after you finish the job. Good luck with this.

May 28, 2011 | Ford Ranger Cars & Trucks

1 Answer

Inner tie rod removal


The first step in replacing the inner tie rod is to remove the tie rod end. It's basically a three step process, where you start by loosening the jam nut that's used to set the alignment (toe-in or toe-out). That jam nut determines how far up the inner tie rod the tie rod end is fixed. The tie rod end is hollow and threaded, so it can be screwed on or off the inner tie rod. Any procedure for removing a tie rod will start by telling you to count the turns you unscrew the tie rod end, something that I didn't do, and I'll save the explanation for the end:-) After you loosen the jam nut, you remove the cotter pin from the post on the outer tie rod ball joint, and unscrew the nut that holds the ball joint into the tapered fitting on the steering knuckle (video to right). After you pop the outer tie end free of the steering knuckle, you can unscrew the tie rod end. from the inner tie rod, but you need to grip it with something. Inner tie rods normally have some flat surfaces or a splined surface for grabbing with pliers. In this case, I needed two pairs of visegrips and a clamp to hold the visegrips on the inner tie rod from moving in order to get the outer tie rod end broken free and turning easy. That video is below. I happen to own the shop manuals for my Dodge Omni, so I was able to study the procedure for replacing the inner tie rod in detail. I didn't follow it for a couple reason. First, they show my type of power steering rack (Saginaw vs TRW) needs to be removed from the car to change the inner tie rod. That's a lot of extra work, not to mention the fact I buried one of the crossmember bolts in my unibody and flooring repair! So I went with an inner tie rod removal kit from Harbor Freight, manufactured by U.S. General (in Taiwan). The tool is very simple, basically a large steel tub with a snap in opening for a large crows foot insert on one end and a 1/2" socket drive on the other end. The kit is shown in the photo to the lower left (which I need to replace), and a video of the procedure is shown below. The kit wasn't quite right for my car, I had to use an oversized crows foot and the ball joint housing on the inner tie rod was too long, so the flats on the housing were barely held with the crows foot positioned by hand at the very end of the tool. But I got it out.

Dec 16, 2010 | 1992 Buick LeSabre

2 Answers

Am changing the inner tie rod on a 2000 cirrus with a 2.5 and cant figure out how to get old one off


to get the inner tie rod out you need an inner tie rod tool, it's a long tube that fits a 1/2 inch drive rachet and there's different size adaptors that go into the end of it to fit over the tie rod, find the right size put into tool, put over tie rod and brake it loose, reverse for installtion.

Nov 18, 2009 | 2000 Chrysler Cirrus

1 Answer

99 Park Avenue Inner Tie Rod removal


best thing i can tell you is to purchase a haynes auto repair manual at any auto parts store. 17$ it'll tell you step by step instructions.

Jul 01, 2009 | 1999 Buick Park Avenue

1 Answer

Loose inner tie rods on '97 Dodge Dakota Sport 2WD


corect size wrench should work. count the number of turn it takes to remove each unit make note and install new units using those numbers

Jun 28, 2009 | 1997 Dodge Dakota

2 Answers

Replacing tie rods


Maybe just a tie rod fork ...you can probably get a loaner free of charge (just requires a deposit) from Auto Zone or one of the chain parts stores.

Apr 01, 2009 | 1991 Mercury Sable

2 Answers

1997 dodge Intrepid: inner tie rod


To Steering Gear Bolt 90 Nm (66 ft. lbs.) Jam Nut 75 Nm (55 ft. lbs.)
NUMBER: 19-001-01
GROUP: Steering
DATE: Mar. 23, 2001
THIS BULLETIN SUPERSEDES TECHNICAL SERVICE BULLETIN 19-003-00 REV A, DATED OCTOBER 6, 2000 WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE PART NUMBER CHANGES AND ADDITIONAL MODEL YEAR.
WARNING: FAILURE TO ACHIEVE A MINIMUM TORQUE OF 100 NM (74 FT. LBS.) MAY RESULT IN THE ATTACHING BOLTS LOOSENING AND FRACTURING. THIS COULD RESULT IN A SUBSEQUENT LOSS OF STEERING CONTROL. BENDING THE RETAINING TABS ALONE WILL NOT PREVENT THIS.

SUBJECT:
Loose Steering

OVERVIEW:
This bulletin provides service procedures and parts information for the inner tie rod bushings.
MODELS:
1993 - **2001 ** (LH) Concorde/Intrepid/LHS/New Yorker/Vision/300M
SYMPTOM/CONDITION:
Loose feel or clunk in the steering wheel as the wheel is moved from side to side.
DIAGNOSIS:
Observe the inner tie rod to steering gear attaching point while moving the steering wheel from side to side. If there is movement between the gear and inner tie rod, perform the Repair Procedure. If no movement is evident further diagnosis of the condition will be required.
DISCUSSION:
The inner tie rod bushings have previously been serviced with the tie rod assembly. This bulletin releases the parts, service procedures, and special tool necessary to service just the bushings. Subsequent service manuals will contain the Repair Procedure.

Jan 13, 2009 | 1994 Dodge Intrepid

2 Answers

Replacing outer tie rod on a 2000 dodge neon


put the tie rod back in and thread the nut on. then you turn the inner tierod with a pipe wrench or a big pair of channel locks. you can spray the threads with pb blaster or wd-40. also if ya have a propane torch this helps loosen the threads. apply heat to the outer tierod do not heat the inner. good luck jimmy

Oct 03, 2008 | 2000 Dodge Neon

Not finding what you are looking for?
1991 Dodge Spirit Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...