Need to know lbs of torque and sequence for the heads on a 1995 jeep wrangler with a 2.5

Question 1

1helpful

2answers

98 Jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs

Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 • Jeep Wrangler Cars & Trucks

1helpful

2answers

Cylinderhead torque settings

I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

If you need further help, reach me via phone at https://www.6ya.com/expert/tasa_06404e20147f8840

Aug 22, 2014 • 1995 Pontiac Grand Am

0helpful

1answer

Need head bolt torque specs for a 1996 saturn sl

Quote:

Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 • 1996 Saturn SL

1helpful

1answer

Engine head bolts

most automotive parts suppliers will offer you the torque specks and sequance of torque just call them

Jul 20, 2012 • Jeep Cars & Trucks

0helpful

1answer

Need torque specs foe a 2000 jeep with a 4.0 to be spacific i need the mains rods and head

Hello mooredavid42,

The Head bolt torque is as follows:

1. Tighten all bolt in the sequence shown in the image below to 22 ft. lbs.
2. Tighten all bolt in the sequence shown in the image below to 45 ft. lbs.
3. Check all bolt to verify they are torqued to 45 ft.lbs in the sequence shown below.
4. Tighten bolts in sequence:
a. Bolts 1-10 to 110 ft.lbs.
b. Bolt 11 to 100 ft. lbs.
c. Bolts 12-14 to 110 ft.lbs.

If you are reusing the head bolts carefully check the bolts for necked down threads.

The main bearing cap bolts are torqued to 80 ft. lbs.

The connecting rod nuts are torqued to 33 ft. lbs.

I hope this helps.

Regards,

Jerry

Aug 24, 2011 • Jeep Cherokee Cars & Trucks

1helpful

1answer

How many pound you torque for jeep wrangler 4 cyl. year 97 head gasket

Tightening Sequence

8 - 4 - 1 - 5 - 9
7 - 3 - 2 - 6 - 10

Pass 1 - 22 ft/lbs.
Pass 2 - 45 ft/lbs.
Pass 3 - # 7 - 100 ft/lbs.
Pass 3 - All others - 110 ft/lbs

May 26, 2011 • Jeep Wrangler Cars & Trucks

3helpful

1answer

WHAT IS CYLINDER HEAD BOLT TORQUE ON A 1988 JEEP CHEROKEE LTD. 4.0?

Torque settings are 110 ft LBS for nine of the ten bolts one bolt is 100 ft LBS /#1 Tighten all bolts in sequence 1 to 10 at 22 ft LBS #2 tighten all bolts 1 to 10 at 45 ft LBS #3 tighten all bolts 1 to 6 at 110 ft LBS #4 bolt #7 at 100 ft LBS #5 BOLT 8 TO 10 AT 110 FT LBS . HEAD TIGHTEN SEQUENCE - standing at front of car bolts down left side are 8/4/1/5/9 bolts down right side are 7/3/2/6/10. left side meaning distributor side.

Oct 07, 2010 • 1988 Jeep Cherokee

1helpful

1answer

Does anyone have the bolt torque specifications for a ford 1995 5.8L. I need the cylinder heads, crankshaft mains and connecting rod torque.

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

May 31, 2010 • 1995 Ford F150 Styleside Regular Cab

0helpful

1answer

1991 jeep cherokee sport 4.0

For your 1991 Jeep Cherokee 2WD 4.0L MFI :
Foot pounds (Final torque)

Note:
Torque sequence ------------------
front | 12 8 4 1 5 9 13 |
of | |
engine | 11 7 3 2 6 10 14 |
------------------
Final torque must be reached in 3 equal steps
Step 1: torque all bolts (except bolt 11)
to 110 Ft/Lbs
Step 2: torque bolt 11 to 100 Ft/Lbs
Recheck final torque in sequence

Sep 30, 2008 • 1991 Jeep Cherokee Briarwood

Question 2

Jeffrey Turcotte

Jeep Master 8,991 Answers
Posted on Sep 23, 2010

Jeffrey Turcotte

Jeep Master

Joined: Aug 22, 2010

Answers

8991

Questions

7

Helped

4370353

Points

33683

From autozone.com:
To install:

Thoroughly clean the gasket mating surfaces. Remove all traces of old gasket material. Remove all carbon deposits from the combustion chambers. Lay a straightedge across the head and check for flatness. Total deviation should not exceed 0.001 in. (0.025mm).

The cylinder head gasket used on the 2.5L engine is a composition gasket. The gasket is to be installed dry. Do not use gasket sealing compound on the gasket.

Fabricate 2 cylinder head alignment dowels from 2 used cylinder head bolts. Cut the head of the longest bolt off below the hex head. Then cut a slot in the top of the dowel to allow easier removal with a screwdriver.
Install one dowel in bolt hole No. 10 and the other dowel in bolt hole No. 8.
Place the cylinder head gasket over the dowels with the numbers facing up.
Place the cylinder head over the dowels.
Coat the threads of bolt No. 7 only, with Loctite PST sealant or equivalent.
Install all head bolts except Nos. 8 and 10.
Tighten the bolts in the sequence shown in the illustration to the following:
1. Tighten bolts 1 through 10 in sequence to 22 ft. lbs. (30 Nm).
2. Tighten bolts 1 through 10 in sequence to 45 ft. lbs. (61 Nm).
3. Recheck bolts 1 through 10 in sequence to verify that they are 45 ft. lbs. (61 Nm).
4. Tighten bolts 1 through 6 in sequence to 110 ft. lbs. (149 Nm).
5. Tighten bolt 7 to 100 ft. lbs. (136 Nm).
6. Tighten bolts 8 through 10 to 110 ft. lbs. (149 Nm).

During the final tightening sequence, bolt No. 7 will be tightened to a lower torque than the rest of the bolts. Do not overtighten bolt No. 7.

Connect the temperature sending unit wire.
Install the spark plugs.
Install the compressor.
Install the compressor/alternator bracket mounting bolt.
Adjust the alternator drive belt.
Install the air conditioning compressor drive belt.
Install the intake and exhaust manifolds.
Install the power steering pump bracket.
Install the pushrods. Keep them in order!
Install the rocker arms. Keep them in order!
Thoroughly clean the mating surfaces of the head and rocker cover and install as outlined earlier in this section.
Install the air cleaner.
Connect the hoses at the thermostat housing.
Connect the battery ground.
Fill the cooling system.

Related Topics:

Trustworthy Expert Solutions

Need to know lbs of torque and sequence for the heads on a 1995 jeep wrangler with a 2.5

1 Answer

Jeffrey Turcotte

Add Your Answer

Attachments: Added items

Related Questions:

What is the torque sequence of the head bolts on a 1999 Jeep Cherokee 4.0?

Head bolt pattern 4.0 - Jeep Cherokee Forum

98 Jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs

Cylinderhead torque settings

Need head bolt torque specs for a 1996 saturn sl

Engine head bolts

Need torque specs foe a 2000 jeep with a 4.0 to be spacific i need the mains rods and head

How many pound you torque for jeep wrangler 4 cyl. year 97 head gasket

WHAT IS CYLINDER HEAD BOLT TORQUE ON A 1988 JEEP CHEROKEE LTD. 4.0?

Does anyone have the bolt torque specifications for a ford 1995 5.8L. I need the cylinder heads, crankshaft mains and connecting rod torque.

1991 jeep cherokee sport 4.0

Not finding what you are looking for?

Cars & Trucks

What is the torque sequence of the head bolts on a 1999 Jeep Cherokee 4.0?

Ask a Question

Check Out the Latest Top Trucks Report!

Top Jeep Experts

ZJ Limited

Ronny Bennett Sr.

Thomas Perkins

Are you a Jeep Expert? Answer questions, earn points and help others

Manuals & User Guides

Http://public.mvlan.net/content/Jeep/R...

Http://www.hemetchrysler.com/pdf/wrang...

Related Topics:

Trustworthy Expert Solutions

Need to know lbs of torque and sequence for the heads on a 1995 jeep wrangler with a 2.5

1 Answer

Jeffrey Turcotte

Add Your Answer

Attachments: Added items

Related Questions:

What is the torque sequence of the head bolts on a 1999 Jeep Cherokee 4.0?

Head bolt pattern 4.0 - Jeep Cherokee Forum

98 Jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs

Cylinderhead torque settings

Need head bolt torque specs for a 1996 saturn sl

Engine head bolts

Need torque specs foe a 2000 jeep with a 4.0 to be spacific i need the mains rods and head

How many pound you torque for jeep wrangler 4 cyl. year 97 head gasket

WHAT IS CYLINDER HEAD BOLT TORQUE ON A 1988 JEEP CHEROKEE LTD. 4.0?

Does anyone have the bolt torque specifications for a ford 1995 5.8L. I need the cylinder heads, crankshaft mains and connecting rod torque.

1991 jeep cherokee sport 4.0

Not finding what you are looking for?

Cars & Trucks

What is the torque sequence of the head bolts on a 1999 Jeep Cherokee 4.0?

Ask a Question

Popular Questions

2002 jeep wrangler 6 cylinder:

Why does check eng light come on and engine starts to sputter

Poor gas mileage on my jeep liberty

I Need to see the fuse box diagram for a 1991 jeep

Heater blows cold air

Check Out the Latest Top Trucks Report!

Top Jeep Experts

ZJ Limited

Ronny Bennett Sr.

Thomas Perkins

Are you a Jeep Expert? Answer questions, earn points and help others

Manuals & User Guides

Http://public.mvlan.net/content/Jeep/R...

Http://www.hemetchrysler.com/pdf/wrang...