Question about 1991 Porsche 928

1 Answer

I CANT GET INSIDE MY PORSCHE 928GTS

HELP IVE GOT A PORSCHE 928 THE REMOTE HAS SET TO VALET MODE WHICH HAS SET,I CANNOT OPEN THE DOORS TO GET INSIDE MY CAR AS THE BATTERY IS FLAT AND THERES NOT ENOUGH POWER TO RESET VALET MODE THERE ARE NO DOOR LOCKS OUTSIDE MY CAR EITHER.......H E L P

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Go to your dealer.

Posted on Jun 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the battery from porsche 928


Remove rear carpet. Remove spare tire in recessed tire compartment. There will be a small hatch with a plastic white lever that you have to swing open. Once the door is open, remove ground (black) first, then the positive red side. Clean terminals and also clean ground to rear hatch from battery.

Oct 06, 2014 | 1986 Porsche 928

1 Answer

How do I turn the alarm off on my 1994 928 S4?


You have a bad connection most likely in the door(s) for the alarm circuit. You will have to remove the door panel on both doors and check the wiring for shorts and bad / corroded connection. Also, sometimes the door locks will not be synced between the two from doors. You will have to close the doors and lock/unlock them so that they both unlock at the same time. Search www.rennlist.com for further in depth answers on the 928.

Jul 11, 2014 | 1984 Porsche 928

1 Answer

Can't find the fuse box on my 1983 porsche 928


hello there
it is located by the passengers feet,under the carpet towards the front you will find a wooden door just lift it up...

proporsche

Mar 28, 2011 | 1983 Porsche 928

1 Answer

I have a viper alarm on my car that wont shut off nor i cant start the car..and i have tried the button under my dash, how Can i shut it off??


was it a professional or shade tree install? the following is off vipers website:
disarming without a remote control
This feature allows you to disarm the security system without the
Remote Control should it be lost, damaged, or disabled. In order to
disarm the system without a remote remote control, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON position.
Press the Valet button the
preset number of times (one to
five times) within 15 seconds. After five seconds the system will
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
if that doesn't work try this other

valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the Remote Control, but
all convenience functions (door locks, trunk release, etc.) will
continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.

May 08, 2010 | 1994 Honda Civic

1 Answer

Vehicle is stuck in valet mode. Steering column is locked. Vehicle is a 2006 Jaguar XJ8L. Cannot open the glove box to get the owner's manual.The battery is fine.


Open the boot lid and drivers door, and switch on the ignition. Rock the valet switch, in the centre console, 5 times. The system will chirp to indicate it has entered learning mode.

On models with seat/mirror/steering wheel memory functions, the first remote will be linked to memory 1, second to memory 2 etc.

Press the larger, lock, button of the remote. The system will chirp to confirm it has got the signal. If it doesn't receive any signals for 15 seconds, it will chirp twice and exit learn mode.

To programme further remotes, rock the valet switch once. The system will chirp twice for remote number two, three times for number three etc, then press the lock button of the remote as above.

When finish, wait 15 seconds for the system to time out and chirp twice, turn off the ignition, close the doors and boot lid and the job is done!

Mar 07, 2010 | 2006 Jaguar XJ8

1 Answer

Cant get my 99 xj8 out of valet mode, and my trunk will not open.


There are Valet keys (often with a green knob) that will
only unlock the front doors and the ignition but not the
glove box nor boot/trunk.

When either the front door locks or the console button is
pressed, all the doors should lock. Likewise, when either
front door is unlocked, all the doors fuel filler lid and if
selected, the boot will also unlock.

Boot lock has three positions. Unlocked to the left,
automatic with the doors in the center, always locked to the
right. Simply remove the key in what ever position you desire.

The locks can get confused and not work correctly. Simply
sit in the car and manually lock all the doors. That will
usually get the locking module sane again.

Feb 28, 2010 | 1999 Jaguar XJ

1 Answer

Porsche 928


open trunck , look behind rear panel look for plastic nut ,loosen and pull on tail light .

Nov 01, 2008 | 1993 Porsche 928

1 Answer

Cannot get car out of "Valet mode"


First start by looking inside the cars fuse box, there should be a fuse named "ROOM". Take it out and check if its still good. If not replace with the same amp fuse.

Aug 27, 2008 | 2001 Nissan Maxima

1 Answer

Wont go into program mode


yes there is actually if you have a valet switch there is a code you set in that gives you control over setting the keyless remote code i dont have the specs and you would probably have to take to dealership so they could show you how to set up valet switch for keyless entry since i do not have a book for that spec also theres this link that they can help set up over the keyless entry remote by there techs call the number give them alarm model and info on truck
http://www.remotesunlimited.com/?OVRAW=car%20alarm%20remote&OVKEY=car%20alarm%20remote&OVMTC=standard&OVADID=2211521522&OVKWID=21052597022
heres the link call the tech they sale to all dealers and have techs on hand during service hours to help

May 22, 2008 | 2003 Ford F150 Regular Cab

Not finding what you are looking for?
1991 Porsche 928 Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

555 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...