Question about 1999 Ford Windstar

2 Answers

Codep1309 1999 windstar

What is the code on a ford windstar 1999, p1309 , theresa

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

P1309 is a code that occurs when the PCM diables the misfire counter due to com. issues between cam pos sensor and crank sensor. generally a bad cam sensor

Posted on Apr 18, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 183 Answers

For which code you want for you car model given by you.

you have to specify you requirements totaly,

THNX

Posted on May 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

P1309 ignition misfire


This should be a Ford engine - so according to the RangerStation website, the code is for the cam position synchronizer sensor is not installed correctly or not working. The sensor is telling the computer the cam timing is off.
You may need a book or internet search to test it and repair it.

Jul 10, 2012 | 1999 Mazda Pickup

1 Answer

Showing Code P1309. Replaced the cam sensor and still showing the code or CMP. What can it be?


You may need to replace the PCM, engine computer. very rare issue. Personally, I would leave it. It is only there to tell you if a cylinder is not firing. You will know if one is.

HD41 CHECK CMP SENSOR OUTPUT
  • Connect PCM.
  • Connect digital multimeter.
  • Start engine and vary engine RPM.
  • Measure voltage between CMP and PWR GND circuits at the PCM harness connector.
Does AC voltage vary greater than 0.1 volt AC? Yes No VERIFY the correct installation by referring to the Electronic Engine Controls, Section 303-14 in the Workshop Manual. If CMP is installed properly, REPLACE PCM (refer to Section 2 , Flash EEPROM). REPLACE CMP sensor. COMPLETE Misfire Monitor Repair Verification Drive Cycle.

----------------------------------------------------------------------------------------------
P1309 - Misfire Monitor Disabled When the misfire monitor is disabled, usually due to the input signal generated by the camshaft position (CMP) sensor, by sensing the passage of teeth from the CMP wheel.
  • Camshaft position sensor
  • Powertrain control module
  • ECT, MAF, and CKP sensors
Verify the CMP is installed correctly and not out of synchronization.

Aug 05, 2011 | 1999 Ford Windstar

1 Answer

Codes p1309


Cam sensor code, its mainly a misfire code, the worst will be to replace the ECM its better that you replace the cam sensor first, that should solve the problem you have

Jun 04, 2011 | 2000 Ford Windstar

1 Answer

Code P1309 on a Ford Winstar 1999 3.8 lts. Mexico


Code PO1309 : Misfire Monitor Failure Description : When the misfire monitor is disabled,usually due to the input signal generated by the camshaft position sensor, by sensing the passage of teeth from the camshaft position wheel. Possible Causes : PCM(power train control module), Mass Air Flow Sensor, Engine Coolant Temperature Sensor, Crank Shaft Position Sensor, Camshaft Position Sensor.

Jun 01, 2011 | 1999 Ford Windstar

1 Answer

2001 ford mustang 3.8 v6 p1309 code . what could be the problem?


P1309--Misfire Monitor Disabled

When the misfire monitor is disabled,usually due to the input signal generated
by the camshaft position sensor

Possible Cause---

Cam Position Sensor
Powertrain Control Module
ETC,MAF,CKP

Verify CMP is installed correctly


You need a local repair shop to check it out

Nov 10, 2010 | 1999 Ford Taurus

1 Answer

Engine code p1309 P/S advice on repair


The definition of this code is:
P1309 Engine Misfire Detection Monitor not enabled

It's a problem with the detection circuitry, not a detection of a engine misfire condition. I found this quickly on the net:
Diagnostic Trouble Code (DTC) P1309 indicates Misfire Detection Monitor is not enabled.

Breakout box installed, PCM disconnected. Connect digital multimeter between PCM test pin 85 and test pins 51 or 103. Bump engine in short burst with the starter without starting engine for at least 10 engine revolutions. Answer this question: Does digital multimeter reading switch between low (less than 2.0 volts DC) and high (greater than 8.0 volts DC)?

If Yes, Verify correct installation by referring to the Powertrain/Engine Group in the Workshop Manual. If the CMP is installed properly, REPLACE PCM. RESTORE vehicle. RERUN Quick Test.

If no, REPLACE CMP sensor. RESTORE vehicle. COMPLETE Misfire Monitor Repair Verification Drive Cycle. RERUN Quick Test.

The CMP sensor is the Camshaft Position Sensor.

Nov 08, 2010 | 2000 Ford Taurus

1 Answer

Code p1309


Diagnostic Trouble Code (DTC) P1309 indicates Misfire Detection Monitor is not enabled, replace the cmp sensor.

Aug 28, 2010 | 1999 Ford Taurus

1 Answer

My car have problen code P1309 plz help me


HI, The P1309 can be set due to a couple of problems the common being the CPS camshaft position sensor failed. There are other components that can cause this code to set including the ECT engine coolant temp, MAF mass air flow, CKP crank shaft position.There are no simple test that can be done at home but this code is usualy quick to diagnose for a good tech.

Aug 26, 2010 | 2001 Ford Taurus

1 Answer

1998 ranger 4.0 eng. code p1309 WHAT?


Check the Camshaft position sensor it may be dead or out of sync

Jul 18, 2010 | 1999 Ford Ranger SuperCab

1 Answer

1999 ford windstar has a misfire code


Look at the coil pack, these are known to develop cracks, usually on the underside in the resin, you have to remove it to tell. It is much easier to reomve with the wiper cowl removed.

Apr 06, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
1999 Ford Windstar Logo

Related Topics:

708 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...