Question about 2000 Daewoo Leganza

1 Answer

Map sensor trying to figure out exactly where this goes?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

HI
the (MAP) sensor is one of (ECU) engine control unit sensors
it was determine the engine manifold pressure and send it as electrical signal to the (ECU) to calculate the air volume & fuel injection to the engine

WITH MY BEST WISHES

Posted on Jul 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2003 nissan altima trying to figure out were the MAP sensor located.Can you help me plze?


There is no MAP (Manifold Absolute Pressure) sensor in a 2002 or later altima. This altima uses a MAF (Mass Airflow Sensor). It is in the intake and has a clip with 5 prongs. God-Bless!

Mar 02, 2015 | Nissan Cars & Trucks

2 Answers

94 camry died and won't start we have spark, fuel and compression and a code 31, changed the map sensor still no start


Yes I do believe that fuel is there. Are the injectors working, some time you have all but no fuel. While cranking check if power is there for injector socket.remove the air cleaner pipe the to the inlet manifold spray 2,3 puf of aero start and see if she run for few second. Take care as you spray, first spray and then start the car
If yes you can figure it out the problem
Let us know how it goes. i hope this is some help to you
AD

Jun 12, 2014 | 1994 Toyota Camry

1 Answer

Wiring on map sensor


Some of those models had a MAP Sensor and some didn't.The mazda and the Ford ranger are the exact same truck with the exception of the grill and tail lights. I am not sure if your saying that you have a map sensor and no wire or a wire and not map sensor.If there is no wire for a map sensor then you truck does not require one. If it has the wire then you will have to get a map sensor.The trucks that don't have a map sensor will have a Mass Air Flow Sensor, located at the top of the air filter box.
I hope this will help you.

Apr 18, 2014 | 1994 Mazda 2WD B Series Pickup

1 Answer

2002 jeep map sensor problems


Not exactly sure what you're describing. Incorrect voltage to or from Map sensor? Map sensors are very sensitive. I clean mine with a Map Sensor Spray cleaner every time I change the Air filter. Check to see if the fine, almost hair like wires in the Map sensor are broken...replace and/or clean if necessary. Best of luck resolving this problem.

Mar 31, 2014 | 2002 Jeep Grand Cherokee

1 Answer

Where is the map sensor located on a 1.9 litre vw jetta?


For exact location and replacing procedure of VW jetta MAP sensor,click the link below and follow the details with diagrams:-----Where is MAP Sensor Located on VW Jetta http://technoanswers.blogspot.com/2012/11/where-is-map-sensor-located-on-vw-jetta.html
---------These will help.Thanks.

Nov 25, 2012 | Cars & Trucks

1 Answer

Map sensor


Manifold Absolute Pressure Sensor

Print


OPERATION

See Figures 1, 2 and 3


0900c1528003c4d9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: MAP sensor location-2.4L engine


0900c1528003c4da.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: MAP sensor location-3.0L engine


0900c1528003c4db.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: MAP sensor location-3.3L and 3.8L engines
The PCM supplies 5 volts of direct current to the Manifold Absolute Pressure (MAP) sensor. The MAP sensor then converts the intake manifold pressure into voltage. The PCM monitors the MAP sensor output voltage. As vacuum increases, the MAP sensor voltage decreases proportionately. Also, as vacuum decreases, the MAP sensor voltage increases proportionally.
With the ignition key ON , before the engine is started, the PCM determines atmospheric air pressure from the MAP sensor voltage. While the engine operates, the PCM figures out intake manifold pressure from the MAP sensor voltage. Based on the MAP sensor voltage and inputs from other sensors, the PCM adjusts spark advance and the air/fuel ratio. The MAP sensor is mounted to the intake manifold, near the throttle body inlet to the manifold. The sensor connects electrically to the PCM.


TESTING

See Figures 4, 5, 6 and 7


0900c1528003c4dc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Disengage the MAP sensor connector-3.0L engine shown

WARNING When testing the MAP sensor, make sure the harness wires do not become damaged by the test meter probes.

  1. Visually check the connector, making sure it is attached properly and that all of the terminals are straight, tight and free of corrosion.



0900c1528003c4dd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: MAP sensor connector terminal identifications: (A) 5-volt supply, (B) sensor signal, (C) ground-3.0L engine shown


0900c1528003c4de.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: MAP sensor connector terminal identifications-2.4L, 3.3L and 3.8L engines


0900c1528003c4df.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Using a digital volt-ohmmeter, test the MAP sensor voltage-3.0L engine shown

  1. Test the MAP sensor output voltage at the sensor connector between terminals B and C (2.4L, 3.3L and 3.8L engines), or A nd B (3.0L engine).
  2. With the ignition switch ON and the engine not running, the output voltage should be 4-5 volts. The voltage should fall to 1.5-2.1 volts with a hot, neutral idle speed condition. If OK, go to the next step. If not OK, go to Step 5.
  3. Test the PCM terminal 36 for the same voltage described in the previous step to make sure the wire harness is OK. Repair as necessary.
  4. Test the MAP sensor ground circuit at the sensor connector terminal A (2.4L, 3.3L and 3.8L engines) or C (3.0L engine) and PCM terminal 43. If OK, go to the next step. If not OK, repair as necessary.
  5. Test the MAP sensor supply voltage between the sensor connector terminals A and B (2.4L, 3.3L and 3.8L engines) r A and C (3.0L engine) with the ignition key in the ON position. The voltage should be about 4.5-5.5 volts.
  6. There should also be 4.5-5.5 volts at terminal 61 of the PCM. If OK, replace the MAP sensor.
  7. If not, repair or replace the wire harness as required.


REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
The MAP sensor is mounted on the intake manifold near the throttle body inlet to the manifold.

  1. Disconnect the negative battery cable.
  2. On the 3.0L engine only, disconnect the vacuum hose from the MAP sensor.
  3. Detach the electrical connector from the MAP sensor.
  4. Unfasten the mounting screws, then remove the MAP sensor from the vehicle.

To install:
  1. Install the sensor onto the intake manifold and tighten the mounting screws to 35 inch lbs. (4 Nm).
  2. Attach the sensor electrical connector.
  3. On the 3.0L engine, connect the vacuum hose to the MAP sensor.
  4. Connect the negative battery cable.

Jul 21, 2012 | 1997 Plymouth Voyager

2 Answers

Im trying to change the map sensor but I need help to know where it exactly located?


check the hose a fat like 3" or more tube that is attached to the cover of your air filter its just before the air filter. (I think, thats where it is on my 2000 eldorado northstar)

Jul 16, 2011 | 2004 Chevrolet TrailBlazer

2 Answers

I have 2 pending codes for a 99' pontiac grand prix gt. p0107 map/baro ckt low input.. & p0113 iat sensor 1 ckt high. i need to figure out what these 2 problems come from & what problems will they...


Try unplugging and plugging the map sensor, this device should have manifold pressure hooked up to it, via hose, so check for cracks or leaks. Then clear codes and test again.

Sep 25, 2009 | 1999 Pontiac Grand Prix

1 Answer

Not a 99 but an 04 wiring diagram for map sensor


All wires on the sensor go to the computer, one will be a standard power wire going to the sensor, and the other 2/3 will be resisted signals going from the sensor to the computer

Jul 20, 2008 | 1999 Honda Odyssey

Not finding what you are looking for?
2000 Daewoo Leganza Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...