Question about 1994 Mazda 323

2 Answers

Looking for part number

I wanna know wt da part number of boot gas strut/boot lifter spring of mazda 323f 1997 and mazda 626 1997

Posted by on

  • RAMONTEJADAR Dec 30, 2008

    I WANT TO GET A ELECTRONIC CONTROL UNIT FOR A MAZDA 323F 1995 079700-5272 12V N. DENSO CONTACT RAMONTEJADAR@HOTMAIL.COM


  • Anonymous Mar 12, 2014

    how to change tension pulley on 1997 mazda 626

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

PLEASE BE INFORMED THAT I WANT TO FIND MY MAZDA CAR ELECTRONIC CONTROL UNIT, THE BELOW (5K) CODE WAS MY ORIGINAL BOARD:
BMV9C
5K
BMV9
EGI
BMV9 18 881C
079700-5262
12V DENSON
*005262F*

CAR MODEL:
MAZDA LANTIS 323
1.6 MANUAL
BVV6 (1995 SERIALS)
ENJIN:B6-503910
CASIS:BA1161-MM-500158
COLOR:MA572

Posted on Jul 12, 2008

Do not interchange

Posted on May 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lights inside the car wnt turn on. i suspect its da fuse but i dnt no which fuse it is. and i dnt have the manual. its a mazda 323f 1.5 glx. any ideas where it were it might be.? thanks


check the bottom by the brake and gas pedals or on the driver side of your dash board and when you find the port fuse on the back of the port it will tell you wich fuse is it all fuses are numberd hope this helps.

May 13, 2010 | 1994 Mazda 323

3 Answers

Does This Car Have Rear "Struts" Or Shocks?? What Is the Difference?


THe 93 Mazda has both actually. The shock absorber in this car is just one component of the so called strut assembly. Read on if you want the details: Shock absorbers are simple suspension dampers that control the unwanted spring motion of the vehicle's frame caused by the suspension's springs. Struts, or strut assemblies, basically does the same thing, although they are used on a different type of suspension system and performs another function, which is to provide support for the suspension system.

A strut assembly is composed basically of a shock absorber unit, a coil spring, an upper pivot, and a lower control arm. A lot of vehicles today make use of strut assemblies instead of simple shock absorbers for the suspension system. The most popular of these strut assemblies is the MacPherson Strut for the front suspension and its rear suspension counterpart, the Chapman Strut.

Mazda vehicles are well known for their sporty looks and performance, amazing a lot of auto critics when they accelerate on paved streets and highways. Mazda vehicles, however, also has the capability of running on an off-road track without affecting the comfort that Mazda passengers feel; thanks a lot to the high quality Mazda struts they are equipped with. Original Mazda struts are guaranteed to provide every Mazda passenger a pleasurable ride, whatever kind of trail they may choose to traverse.



Jan 04, 2010 | 1993 Mazda 626

2 Answers

Mazda 323f sport 1999. How do you adjust parking brake?


Where the handbrake lever is,it will be covered by a boot of some sort.Peel this back and beside the lever will be either a rod with a nut on it,or it will have a recess for a screwdriver.with the h/brake off,do the adjustment by tightening it.When it's right, the h/brake should have to be pulled so 7 'clicks' can be heard.Hope this helps

Aug 19, 2009 | 1994 Mazda 323

1 Answer

Remove and install struts on 04 mazda 3


In the rear you DO NOT need a spring conpressor to remove struts. However in the front If your struts have the springs around them, then yes you definatly need a spring compressor. They sell and rent automatic spring compressors but they cost  a couple hundred bucks, but if I was you I would go to an auto parts store and get manually spring compressors they are $30-$50 and you hook them up to the springs and tighten them down with a drill or air gun. If you dont have a drill or air gun you could use a wrench of rachet but that will take forever.

Jun 09, 2009 | 2005 Mazda MX3

1 Answer

Electric aerial mazda 323 P reg


you shuld be able to take the inner plastics out of the boot then you should be able to get to iti have a mazda 323f m rege hatchback that was what i did! hope it works!!!!!!!!

Mar 26, 2009 | 1994 Mazda 323

1 Answer

Toyota previa springs and struts soft


yes there is at autozone they have spring lifters that go between
the spring itself and they are cheap .

Nov 30, 2008 | 1994 Toyota Previa

2 Answers

Boot cannot keep opening every time ope the boot . i have to keep hold boot with one hand .


I think on the ford focus the boot has a spring that is set up to pull the boot up when you open it.

If your boot is not staying open it may be that the spring has either come off or broken. I think there may be a spring either side. One way to check the set up so you know what your looking for would be to go to a dealership and look at a new car - look around - tell them your just looking if they ask and the open the boot and check the spring attachments. When you go back to your own car check to see if the same springs are in place. If one is missing then at least you know what you need.
You can go to the Service desk in the dealership and order the spring or at least check how much it is.

Aug 19, 2008 | 1999 Ford Escort

1 Answer

MAZDA 323F 1990 MODEL


There you go, the prices, i dont know about the charges, sorry, try also go to Amazon.com
here is a link for you:
http://www.google.com/products?hl=en&q=steering+wheel+for+mazda+323f+1990&um=1&ie=UTF-8&sa=X&oi=product_result_group&resnum=1&ct=title

Jun 22, 2008 | 1990 Mazda 323

Not finding what you are looking for?
1994 Mazda 323 Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...