Question about 1993 Ford Ranger SuperCab

2 Answers

Bogs from start to 1500rpm starts good runs good above1500rpms idles good

93 ford ranger 4.0 at 2wd starts good idles good step on the gas from idle and it bogs and pops lift up on the gas and it idles ok step on the gas slowly and it will go right up to 3000rpms fine. just seems to bother when you step on the gas quickly. we changed the coil-wires-02sensor-tps sensor had it on a snap on scan tool and it said rich 02sensor replaced both. any help would be help ful. thanks Bud

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

The idle speed is controlled by the PCM based upon sensor inputs using the Idle Air Control (IAC) valve to regulate air input past the closed throttle plate to the intake.
The PCM controls the IAC using a solenoid to move the valve body that opens and closes the air passage to the intake. The PCM ensures a seamless transition from IAC control to throttle plate control of engine speed using the Throttle Position Sensor (TPS) attached to the throttle plate.
If you pull the electrical connection from the IAC (round body fitting bolted to throttle body) usually the engine will stall. If it doesn't then you may have a vacuum leak. Check hoses and connections are secure. Your symptoms are consistent with a small vacuum leak.

Try holding the idle a bit longer, then the PCM will set a code. So that is what you need to do, try to hold the throttle just off idle to retain the hesitation long enough for the PCM to try a few strategies and settle on the problem and set the code. You can then get the code read at Autozone, Pep Boys or Checker. You need the P0123 number not the description.

Hope that helps!

Posted on May 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,142 Answers

Check the air filter too that should be clean too for a proper engine breath

Posted on May 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 4.0 starts and idles but will not rev up when gas is pressed, bogs down and dies.


Check engine light on? What are the code numbers. The symptoms sound a lot like a bad Mass Air flow sensor.

Aug 16, 2013 | 2004 Ford Ranger

1 Answer

92 ford ranger when first started excessively high idle


Could be a vac leak, or a faulty idle air control valve on the throttle body.
The computer controls idle speed by regulating the amount of air entering the intake.

Sep 23, 2012 | 1992 Ford Ranger

1 Answer

1992 Ford Ranger 4.0 starts, runs and idles fine sometimes. then the next time I start it, it idles rough


your choke Is stuck on the Injector/carborater. when you press the gas It Is lettIng to much aIr In. check the cable on Injectors or If It Is carb get some carb cleaner from your local automotIve retaIler and take the breather off and spray carb. also check around It to kake sure the cable Is.not streatched nor caught.

Feb 23, 2012 | 1992 Ford Ranger

3 Answers

1998 Ford F-150 4.2 V6 starts and idles fine ibut bogs when step


i had a van do this same thing to a tee turned out to be a broken key pin in the harmonic balencer causing the timing to ****** replaced balencer and ran like a dream there is a crank sensor grid on the balencer when the key pin broke it trew the timing off

Feb 28, 2010 | 1998 Ford F150 Regular Cab

1 Answer

My ford ranger idles low and spits gas out the exhaust


Hello,
First confirm it is either gas or eastter. Wayer/condedste collects at the tail oip as a byproduct of the caralyctic converter on cold rngine It normally occurs on firts start of a cokd enginw. the ebgine idles low because it is col, but should reyutn to normsl after warm uo.. If for sure iys gasolinem and the engine runs eiygh, then angihector is bad, good luck. I hope this helped yyou

May 15, 2009 | 1993 Ford Ranger SuperCab

1 Answer

Fuel pump?


Probably stopped up cat

Mar 09, 2017 | 1989 Ford Ranger

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...