Question about 1983 Chevrolet Silverado

1 Answer

How to take a stub shaft off a 1984 turbo -350 transsmission

Stub shaft how to remove and replace it with 2'' longer stub shaft I have 2 transsmission 1 stub shaft is 2" longer then the other

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 87 Answers

Stub shaft is affixed from inside the transmission

Posted on Jun 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 350 twin turbo ,oil getting in turbo and reducing engine power on my 2008 ford 350 diesel


This is a hard question to answer, but I will try to help. I would assume that you have taken some portion of the turbo system off.

First, it is possible for one side to be good and the other to be bad. You would want to look at the exhaust ports from the heads to see if there is oil going to the Turbo from a bad Valve seal from a cylinder or a bad oil ring on a Piston.

Once you are assured that the problem is in the Turbo, there are oil seals on the rotor shafts. If there is a roughness in an oiled bushing or shaft surface, the Turbo slows down. This would reduce power. You may be able to feel the roughness with your hands.

Another Fixya Expert may be able to tell you more about testing the RPM of the Turbo and they may know how to do it without disassembling them. I hope my input has helped.

Feb 14, 2014 | 2008 Ford F-350 Super Duty

1 Answer

My 1984 cutlass calais is burnin threw transmission every 6 months and cant seem to keep a 350 turbo kno longer than a yr


Next time you change it, be sure to flush the entire system out. Including the lines and cooler in the rad. Possibly filings in your oil, and it is shortening the tranny life.

Dec 30, 2010 | 1984 Oldsmobile Cutlass Calais

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


These are the steps you need to follow for this procedure if you have the proper tools.
  1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
  2. Remove hub and bearing to stub axle retaining nut.
  3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
  4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
  5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

Aug 27, 2010 | 1994 Chrysler LHS

1 Answer

Will a turbo 350 fit into a 1990 gmc halfton that has a 700 r4 in it


It will mate to the engine, but the turbo 350 is shorter then the 700R4 and your going to loose the lower first gear ratio in the 700R4 and the OD that the Turbo 350 don't have. It can be done, but your going to have to relocate the transmission cross member and have a longer drive shaft made.

Good luck.

Jan 04, 2010 | 1995 GMC Sierra

2 Answers

Engine swap 5.0 vortec to 350 non computer controled


The computer runs the Transmission from the signals the throttle position sensor, crank shaft sensor, and cam shaft sensor. Your going to have to replace the transmission with an older transmission like the turbo 350 or turbo 400. When it's time to get the car e-tested, that's when your going to run in to problems, due to the year your Chevy is. If your Chevy was a 1985 then you could go with the carb system but with being the newer OBD11 system, your going to have an off road only vehicle with that swap. Why would you want to replace the engine with the 350 carb set up??? There are things you can do to tweak the one in your Chevy free of charge.

Nov 05, 2009 | 1998 Chevrolet K1500

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

2 Answers

Will a 1984 350 cu short block fit a 1993 GMC


No,they're 2 different animals, you'ld need to alter so much stuff to make it work.I'd explain but why? Just don't do it!!

Jun 21, 2009 | 1998 GMC Sierra

1 Answer

Speedometer does not work 1991 GMC Sierra 2500


the turbo 350 doesn't have a output speed sensor like the trans that came with the truck orginaly. You will have to use a cable to drive a pluse generator,or switch the tail shaft housing with a 700r4e housing of the same length,and use the speed sender from the 700r4e or early 4l60e. note the tail shaft is the same splines but the 350 shaft detent hole my not line up with the relucture ring. therfor the output shaft needs to be change to, or have a relucter ring made.

Apr 03, 2009 | 1991 GMC Sierra

1 Answer

V6 to v8


I swapped mine out and put in a 350 with a turbo 350. The rear end is not posi but if that's not a problem the drive shaft will work but you'll have to get a new trans mount. you can get one from Summit or jegs. Also the motor mounts will have to be moverd to the furthest front position. Best to put the mounts in then try the engine for fit before you bolt in the trans. You'll also have to rerun the fuel line to the other side. There are some other minor mods but you do them as you go along.

Sep 28, 2008 | 1984 Buick Regal

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...