Question about 2006 Chevrolet Avalanche

2 Answers


Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The Check Engine light stayed on means an Error Code is set. You will need an OBDII Code Reader to read / reset the code. If you do not have one, take your car to Autozone, they will do it for you FREE. Vote for me if this helps.

Posted on Dec 19, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi *****

Posted on May 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I don't know where my starter is on my 2006 Chevy avalanche

Starters are almost always (99+%) located where the engine block is bolted to the transmission/clutch housing. Depending on what other components are bolted to the engine, you may be able to see and access from the top, but most have to be removed from below. Some are very difficult to get to and may require removal of other components, or loosening engine mounts, etc. Strongly recommend getting a shop manual (Haynes, Chilton, Motor, etc) from an auto parts store for your model. You can also search on YouTube to see if someone has posted a video for your model, or a similar one.

Mar 18, 2017 | 2006 Chevrolet Avalanche

1 Answer

04 Chevy avalanche knock sensors location

Nathan, 2 Knock's are located under intake manifold.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Engine Knock Sensor 2000 06 5 3L Silverado Sierra...

Knock sensor 5 3 4 8 6 0 replacement

05 Chevy Avalanche Knock Sensors

4 8 5 3 6 0 knock sensor replacement GM

Mar 06, 2016 | Cars & Trucks

1 Answer

I removed my instrument cluster from my 2005 chevy avalanche to have it repaired and now my truck won't start with my remote starter

Should send direct to mechanic to check or recheck again maybe you will forget any step on that

Mar 04, 2015 | Cars & Trucks

1 Answer

Remove starter 2003 chev 1500 pickup 5.3 engine

ark your Chevy Avalanche on a level surface, activate the emergency brake and place blocks behind the back tires for safety. Disconnect the negative battery cable with a terminal puller. Raise the front end of the car with a jack for easier access to the starter.

  • 2 Remove the positive battery cable nut and the engine harness ground nut. Disconnect the positive battery cable and ground wire from the solenoid.
  • 3 Unscrew and remove the starter mounting bolts. Place all nuts and bolts in a safe place to prevent loss, such as a baby food jar.
  • 4 Detach the heat shield if necessary. Remove the starter from the vehicle.
  • 5 Take your malfunctioning starter to the parts store with you. Aftermarket distributors remanufacture most of the starters they sell, so you can likely obtain a partial credit toward your new starter by exchanging your old one. Be sure that you take care not to damage the starter in transit, because the better condition it is in, the more you can get for it.
  • 6 Purchase a replacement starter that has the same or higher cranking capacity (power rating) as the original starter. Also, match the bolt patterns, drive gears and electrical connections. Your owner's manual may list specifications or the auto parts technician will help you determine them. Download a free owner's manual by registering with the Chevy Owner Center (see Resources).
  • 7 Install the new starter motor by reversing the removal process. Tighten the heat shield nut to 44 inch pounds (five Nm) and the bolt to 35 inch pounds (three Nm).
  • 8 Torque the starter mounting bolts to 37 foot pounds (50 Nm). Tighten the ground wire retaining nut to 30 inch pounds (3.4 Nm) and the positive battery cable retaining nut to 80 inch pounds (nine Nm).
  • 9 Lower your Avalanche back to the ground. Reconnect the negative battery cable. Turn the key in the ignition to see if your new starter motor functions correctly.
  • Oct 17, 2011 | Cars & Trucks

    1 Answer

    Have an 08 Kia Sorento. Had an after market remote starter installed a year ago. In this past light the check engine light has been coming on. Codes have shown an Oil Control Valve problem (replaced) and a...

    yes its often that dealers will advise that if car starter installed there is no gurentee as well the car if its finish with the gurentee the tech line advises the mechanics to remove any after market devices installed to repair the original system but most of the time the starter is not the problem but it eliminates it sometimes the car starter has extra features that cause problems in the startingcircuit for example when the car starter installed the main wire is put it between the starter and ignition so if the wire is cut to far this causes a lost between the ignition switch and the starter or the module can be damaged and the same thing apears and so on

    Mar 30, 2011 | Kia Sorento LX Cars & Trucks

    2 Answers


    Buy a Haynes manual for the vehicle ( most auto stores carry them). With this manual you can do nearly any repair on the vehicle, they give you step by step directions.

    Feb 05, 2010 | 2008 Chevrolet Avalanche

    2 Answers

    Check Engine light comes on....

    2006 uses OBDII system and you will need a OBDII scanner to check the problem. Now keep in mind that when you do a scan you will get many codes. Usually the first in line is the one that started the problem. Good luck

    Aug 22, 2009 | 2003 Chevrolet Avalanche

    2 Answers

    2006 Chevy Avalanche climate control fan won't turn off. Even when the engine is off. I must remove the fuse to keep it from running.

    Their is a relay/ fuse box under the hood thir is a relay that is probbly sticking corrison on the contacts inside is a commen problem remove the relay and try switching it with a twin relay that controls somethig else in the box and see if it shuts off the fan if so replace the relay avalible at most auto part stores.

    May 22, 2009 | 2006 Chevrolet Avalanche

    Not finding what you are looking for?
    2006 Chevrolet Avalanche Logo

    310 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides