Question about 1993 Jeep Grand Cherokee

1 Answer

Alarm/lock remote i have a 1993 jeep grand cherokee, and it has a remote for the alarm and locks, but the battery died in it. can i replace it myself and have it still be programmed to my car? or do i need to take it to jeep and have it professionally installed and reprogrammed?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Dtgt

Posted on May 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Jeep Grand Cherokee, Changed battery now head lights stay on


make sure the alarm is not on .cycle the key in the drivers door lock and unlock.see if that helps

Nov 03, 2013 | 1993 Jeep Grand Cherokee

Tip

Do it Yourself: Reprogramming the Remote Keyless Entry (RKE)


Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Jeep Grand Cherokee Alarm System (1993-1998)

I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module. If you wanna download this procedure, clic the image.

79482d7.gif

Enjoy Jeep.

on Sep 23, 2009 | 1993 Jeep Grand Cherokee

2 Answers

1996 jeep grand cherokee laredo: I had just bought this jeep from an owner and i locked the doors yesterday. When i went to unlock the door it set off the alarm. I have tried everything possible to...


put the key in the drivers door lock it with the key still in the lock unlock it and then pull the key out do this three times that is the factory built in security programing shut off system for jeeps and chrysler

Mar 11, 2011 | 1996 Jeep Grand Cherokee

1 Answer

I need detailed description on replacing door lock cylinder on 1993 Jeep Grand Cherokee Limited, or tips on disengaging security alarm.


to disengage alarm just disconnect the battery ,the door lock come out easy they are held in with a metal U clip from the back thats all ,nothing complicated and once door panel is off they take seconds to pop out

Mar 04, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I have a jeep grand cherokee laredo 1993, the security system have been activated and now when I start it, it will only stay started for a few seconds. tried turning the key all the way to the right and...


first use your remote, lock-unlock-lock-unlock 5 times. use the key to unlock the door. lock with remote. If this fails, disconnect battery for 5 min. reconnect, should reset control module..

Dec 09, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Security alarm stays on and vehicle wont start


Sure the door lock is bad maybe. with the fuses in and the doors clsed try the other locks some jeeps only reset with the hatch lock as all the others are worn out or don't detect tha t the door is closed

Dec 05, 2009 | 1993 Jeep Grand Cherokee

2 Answers

Alarm wont disarm and unlocking doors does not work any suggestions?


I just had the same problem with my 1995.. believe me its a pain! by the way on the driver side below the steering wheel close to the door there should be a hidden pink (or any color) plastic box which basically controlls the cars security system... i removed it and i was good to go...try that... the only thing though is that you wont be able to lock the doors automaticaly, ull have to do it manually

May 17, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Remote lock no longer works


replace remotes from dealer possible water damage in remotes

Apr 21, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Security system locked on 1993 Jeep


I had the same problem with my '93' Jeep Grand Cherokee. I found that if I keyed my drviers door lock the security system would turn off.

Apr 05, 2009 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...