SOURCE: Remove interior door panel on 2003 BMW 330I
I am assuming that you have a 4 door sedan. If you want to remove the front door panel, it is held on with 4 or 5 torx screws, Under the armrest you will see 2 plastic cap covers. Gently pry the covers loose and the screws are inside. T20 I think. Where the inside release handle is you probably have a decorative strip(wood grain or painted plastic). At the end farthest from the handle, use a plastic wedge, or flat popsicle stick to pry the corner loose and gently pull the strip toward you. There will be 2 more screws under it. If your door has a plastic airbag emblem there is a screw under it. Otherwise there should be 1 screw hiding under the mirror switc on the armrest, or mirror switch cover. Using a small flat edge wedge pry between the panel and body at bottem until the panel pops loose.work your way around the entire panel. The top panel near the glass pulls toward you. Once the entire panel is loose, grabbing the armrest,pull the panel straight upwards. Be careful when pulling up as to not pull too far. Your inner release cable is attached on the backside. When reinstalling the panel make sure that the rubber grommets are on the panel clips..they help keep water out.
SOURCE: Need to replace the driver's door interior door opening assembly
Hi there.
The procedure is roughly the same for all mk3 x types.
You need to remove all the screws on the armrest and on the ashtray, then undo all the plastic clips using screwdrivers on the panel.
You find detailed instructions on links below, I quote:
"
remove two screws at the bottom of the armrest.
pull out ash tray.
remove screw in the middle of the ash tray holder.
pull up on armrest, it should pop up, then pull it out
start at bottom right of door and start popping out the plastic clips (all the way around the door)
(remove speaker wires)
push up door panel - done"
WikiAnswers - How do you remove a rear door panel in a Jaguar XJ6
Also from manual:
Disconnect vehicle battery ground lead.
Remove the door trim pad veneer panel.
Remove the upper trim pad.
Remove the door armrest.
From inside the door pocket, release the puddle lamp (1 Fig.1) securing quarter turn fastener.
Undo and remove fixing (3 Fig.1), (front door only)
Carefully release lower trim pad fir tree fasteners.
To avoid damage and distortion of the door metal, lift the lower trim pad complete with clip and clip retainer.
Carefully pull the trim pad away from the door panel.
Disconnect the multi-plugs (1 Fig.2) and remove the lamp.
Carefully displace the trim pad (2 Fig.1) from the door retaining clips.
Disconnect the multi-plugs (2 Fig.2) and (3 Fig.2).
Remove the door pocket.
Displace and remove the retaining clips and remove the trim..
Refit in the reverse order of the removal procedure. Check the trim pad retainers for damage before refitting.
Before refitting the lower trim pad, remove the clip retainer from the pad and and reposition retainer to the door.
ndo door handle escutcheon screw and remove escutcheon
Remove the door trim pad veneer panel.
Undo and remove the upper trim pad securing screws.
Remove the chrome strip.
Undo and remove the top channel securing nuts.
Displace and remove the top channel assembly.
Place the trim pad aside (Fig. 1).
Refit in the reverse order of the removal procedure.
Thanks Jaguar XJ6 Interior Lights
I will be grateful if you can rate the solution given.
Many thanks.
G.
SOURCE: how to remove interior door panel on a 1997 caravan with ower windowq
Start by removing the negative battery cable from the battery. Then locate and remove the screws that hold the interior door handles in place (they may be hidden by snap in, or snap on covers). Once you have removed the interior door handles, disconnect the wire clips that go to your window and door lock controls.
I personally use a small pry bar to remove the interior door panel; it is held in by plastic snap clips. Try to get as close to, or directly under the snap clips as possible with your pry bar to prevent them from tearing out of the door panel. Once you have released the snap clips, pull the panel upward to remove it. Install in reverse.
I hope this information helps you, and I wish you luck on your repair.
SOURCE: door panel removal
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
SOURCE: How to remove interior door panel on 2002 chrysler t & c???
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
144 views
Usually answered in minutes!
×