Question about 2006 Ford Laser

2 Answers

Ford Laser Oil light doesnt show up?

I have a 1988 ford laser, and when the ignition is turned on, the oil light doesnt show up.The car has, had a full service. Why is this happening? any info is greatly appreciated. Thanks

Posted by on

2 Answers

Check oil sender unit

Posted on Jun 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 375 Answers

Have a mechanical oil pressure test done. This will verify that the engine has sufficient oil pressure, it may be that the light bulb burned out sense it wont come on even when the key is in the start position.

Posted on May 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the oil pressure sensor prevent ignition to the motor? 1999 Ford Laser - KN or Mazda 323


no oil sensor not related

fuel ,spark a broken timing belt

fuel
pump or relay you should be able to hear the fuel pump working
if engine light is on
crank angle sensor

Nov 05, 2016 | Ford Cars & Trucks

Tip

Ford-Lincoln service light 1988-01


LS

2000-01

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the STATUS control to access the System Check mode. Press the RESET button to display OIL LIFE _% RESET FOR NEW. Press and hold the RESET button until OIL LIFE IS 100% is displayed.


Mark VIII


1993-97

When "CHANGE OIL SOON" or "OIL CHANGE REQUIRED" is displayed on the Message Center, turn the ignition on. Press and hold "OIL CHANGE RESET' or the "RESET" button until "OIL LIFE RESET TO 100%" is displayed on the Message Center.


Continental


1989-94

When "SERVICE" is illuminated, on the Message Center, press the "SYSTEM CHECK" button on the right of the display. Then press the "RESET" button. The "SERVICE" symbol and mileage will start to flash. Next, press the "SYSTEM CHECK" and "RESET" buttons at the same time. The display will show "7,200 miles/11,580 km" and will count down from there as long as the buttons are depressed. Release the buttons at the desired service interval.


Continental


1988

When "SERVICE DUE" is illuminated on the Message Center, press the "CHECK OUT" button located below the display. Then press the "RESET" button. The display should now read "SERVICE DONE?" Next, press the "CHECK OUT" button and "RESET" buttons at the same time. The display will show "7,200 miles/11,580 km" and will count down from there as long as the buttons are depressed. Release the buttons at the desired service interval.







on Dec 07, 2009 | Ford Lincoln Continental Cars & Trucks

1 Answer

I need to know the procedure to reset, 'Change Oil warning' on my 2006 Ford Freestar.


On the right side of the steering wheel there is a button that says "setup". Turn the ignition key to the on position, push the setup button and hold it until the change oil warning shows 100%. There should be a message that pops up telling you to push the reset button to the right of the setup button. Push the reset button and hold until the message confirms the oil life has been changed to 100%. Release button turn off ignition key. Now start the engine to make sure the warning light does not come back on. If it does, try again.

Jan 22, 2011 | 2006 Ford Freestar

1 Answer

Does a Ford Laser 1987 GHIA have air filters that need replacing? I am doing my first home own oil & filter change cant see any air-filter?


one their somewhere ,?? but where i wouldnt know because iam in spain and i have never seen one of these cars

Jan 02, 2010 | 2006 Ford Laser

1 Answer

I had the oil changed in my 2005 ford 500 and the oil change light won't reset back to the mileage info.


If you have the hand book that should show you how to reset it.Who ever changed your oil should have reset that for you.On some fords you hold your foot on the gas pedal with the ignition switched on.Keeping it pressed turn of the ignition,And then turn back on with the gas pedal still pressed to the boards.Then leave of gas after 10 seconds,

Jul 19, 2009 | 2005 Ford Taurus

2 Answers

Oil change light does not go off after oil change


Might need to disconnect the battery for a few minutes to reset the computer.

Jun 02, 2009 | 2006 Ford Explorer

1 Answer

Ford laser 1994 station wagon won't start


sounds like the timing is out, the battery is low and the fuel filter may need to be changed. cheers !

Feb 20, 2009 | 2006 Ford Laser

1 Answer

How to stop crank turning with sump in place to undo front pulley bolt on 85 ford laser


I positioned the spanner against subframe and engaged starter motor briefly which loosened the crank bolt..checked first the rotational directions were correct. This is for 1985 Ford Laser/ Mazda 323

Nov 08, 2008 | 2006 Ford Laser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...