1987 toyota pickup 22r engine

Sorry not available in my alldata book ,as for alternator bracket this should be easy to change without any diagram for a proper mechanic worth his salt. Bring engine to TDCno1 but taking the plug out and lower a long thin screwdriver do locate TDC then paint the gears with white paint before taking the old one off .

Should be just a bracket, contact a salvage yard for info and best price. Some times even Ebay has these kind of parts...

Here is a picture of the alternator installed, hope this helps

2005 Ford Mustang 4.0L SFI SOHC 6cyl
Ford Mustang 1999-2005
Alternator - Removal & Installation

3.8L And 4.0L Engines

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Disconnect the negative battery cable.
3. Remove the accessory drive belt.
4. Disconnect the alternator electrical connectors.
5. Remove the alternator shield (4.0L engine).
6. Remove the alternator mounting bolts.
7. Remove the alternator from the vehicle.
8. Installation is the reverse of the removal procedure.

To install:

1. Position the alternator onto engine. Tighten the lower bolt to 35 ft. lbs. (47 Nm) and the upper bolt to 18 ft. lbs. (25 Nm).
2. Install the alternator shield (4.0L engine).
3. Connect the alternator electrical connectors.
4. Install the accessory drive belt.
5. Connect the negative battery cable.

4.6L Engines (Non-Supercharged)

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Disconnect the negative battery cable.
3. Remove the air intake scoop bracket, if equipped.
4. Remove the accessory drive belt.
5. Remove the upper alternator bracket.
6. Disconnect the alternator electrical connectors.
7. Remove the alternator bolts.
8. Remove the alternator from the vehicle.
9. Installation is the reverse of the removal procedure.

To install:

1. Position the alternator onto engine. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).
2. Connect the alternator electrical connectors.
3. Install the upper alternator bracket. Tighten the bolts to 89 inch lbs. (10 Nm).
4. Install the accessory drive belt.
5. Install the air intake scoop bracket, if equipped.
6. Connect the negative battery cable.

4.6L Engines (Supercharged)

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Disconnect the negative battery cable.
3. Remove the accessory drive belt.
4. Raise the vehicle.
5. Disconnect the alternator electrical connectors.
6. Remove the alternator bolts.
7. Remove the alternator from the vehicle.
8. Installation is the reverse of the removal procedure.

To install:

1. Position the alternator onto engine. Tighten the lower bolt to 18 ft. lbs. (25 Nm) and the upper bolt to 37 ft. lbs. (50 Nm).
2. Connect the alternator electrical connectors.
3. Lower the vehicle.
4. Install the accessory drive belt.
5. Connect the negative battery cable.
6. Installation is the reverse of the removal procedure.

More details about this model in Autozone.com (free register).

I hope help you with this (remember rated this help). Good luck.

I can't send you a diagram,but it's not too hard to explain. Loosen off the alternator first. Two bolts, one you can see that goes through a bracket on the engine and another that is directly under that bolt on the bottom of the alternator that goes into the engine. Fit your new belt over the fan first, one blade at a time and on the pulley. Run the belt down to the bottom crankchaft pulley and then across to the alternator. Before you tighten the belt make sure that all 3 pulleys are in a straight line when you look from the side. If not move them so they are. Take a long screwdriver and put it in the hole on top of the alternator bracket and pry the alternator over so the belt is snug and a little bit more. Tighten the top bolt first,but be careful because it can strip the threads. Then tighten the bottom bolt.You will probably have to retighten it after a few days because the belt will stretch. If the belt squeals when you start or rev the engine then it needs to be a little tighter. If you strip the top bolt, just take it out and find a smaller one with a nut and washers and use it with the washers on the front to keep the new bolt from pulling through the bracket. Hope this helps.

Why not eBay? you may be able to find a "lightly" used harness from an appropriate dodge or Chrysler product that uses your engines?
Try for a Repair manual or electrical repair segment for an appropriate Chrysler product with your engine.
http://www.manualslib.com/

I have recently done this twice to my 2000 Grand Caravan with the 3.3l engine.
1) Remove the top plate which is attached to the alternator mounting bracket held in by 3 bolts.
2) remove the alternator bolts securing the altenator to the mounting bracket.
3) pry the alternator off the bottom mounting bracket
4) turn the alternator around show you can easily see the power wires on back of the alternator and remove the 11/32 nut holding the wire to the alternator. Be careful not to drop the nut behind the engine, because you probably will never find it (experienced).
5) Disconnect the wires from the alternator
6) Remove the black cooragated tube running vertical in front of the alternator and remove the tubes hold clip from the suspension wall.
7) Slide the alrernator pully first up through the opening. You may need to rotate the alternator a little so it fits up through.


Chris

go intenet exploer type in 1995 bmw 318 ti engine diagram ,( i just did) and you can download what you need

Here is a picture showing the location of the nine bolts securing the bracket (this engine is out of the car). It is possible to remove the bracket with the alternator in situ, if you have air tools and just about every extension and off-set available. Otherwise, removal of the alternator is usually necessary.

the accessories on 4.3 gm is what they call a horse shoe so all of the pumps etc. that are run by the belt need to be removed(except water pump in most cases)most of the bolts go thru the bracket in to the heads so you wont find too many down on the lower part of the engine.
hope this helps....good luck!