Question about 2005 GMC Yukon Xl Denali

Open Question

Location of trailer brake fuse in a 2005 yukon

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: Where does the fuse go for the trailer brake control

try looking under the hood, there is a fuse box on the driver side

Posted on Jan 13, 2009

  • 9 Answers

SOURCE: No brake lights on 96 yukon

The brake fuse #1 is located inside the truck below the steering column. I am assuming you have verified there is 12v power at the fuse & thru the brake lamp switch (orange wire power in & white wire power out, when pedal depressed) at all times. After the brake lamp switch , power goes (white wire) to the Turn signal/hazard lamp switch & out (dark green wire-rt brake lamp & yellow left brake lamp)

Posted on Feb 16, 2009

  • 32 Answers

SOURCE: 2005 trailblazer trailer light connection

Should be in the front under the hood in the main fuse box on the left side of vehicle . look for the aux fuses for the traler plug.

Posted on Mar 25, 2009

  • 88 Answers

SOURCE: rear brake lights don't work

you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

Posted on May 23, 2009

arauzvictor1
  • 466 Answers

SOURCE: trailer park light fuse ALWAYS blows on my yukon

If the fuse blows is because you have a cut in the making or in the trailer wiring

Posted on Nov 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No trailer Brake Lights right or left side


Try the specified fuses in the under hood fuse center. they are common to blow.

Mar 28, 2014 | 2004 GMC Yukon XL

1 Answer

Trailer wiring


OK ON SOME OF THE TRAILER BRAKE PLUGS ( THE PLUG FROM BRAKE BOX TO TRUCK ) THE POWWER WIRE IS IN THE WRONG PLACE ,THE PIN AT TRUCK SIDE MAY NEED TO BE MOVED IN THE PLUG,

Feb 05, 2014 | 2001 GMC Yukon XL

1 Answer

Yukon brake light


You have power at the fuse. The brake light switch has two wires on it, one is the supply from the fuse the other is to the lights, Check for volts at the switch (yes), bridge the two wires then follow the wiring checking for a live. Start at a light and work your way back up the loom checking all connecting sockets, has the vehicle a trailer socket, check the multi-plug where it picks up the wiring.

Jan 03, 2014 | Cars & Trucks

1 Answer

I have a 05 Denali XL 6.0 and i can't find the trailer brake harness under the dash. Please help!!


Hi, the provision for the electric brake controller is located in the electrical center , just to the right of the parking brake. There is a plastic nut, that holds the cover on, and beneath this cover are ports where a connector may be plugged in. A factory harness must be obtained from a Chevy, or GMC dealer for the install. This harness will be labled with wire locations, as it will be attached to your brake controller, then plugged into the slot in the upper l/h corner of the electrical center. The plug will only fit in the appropriate slot. You will then need to put the provided J- fuse into the underhood fuse block. Tis should be the only missing fuse. You should be well on your way, after these few easy steps. Good luck...Coop

Oct 15, 2010 | 2005 GMC Yukon Xl Denali

1 Answer

Braking lights and turn signals not working


Did you check the brake and signal light bulbs? If something happened that blew a fuse, chances are you probably lost some bulbs too. that should fix your problem

Oct 20, 2009 | 1999 GMC Yukon

2 Answers

Right side trailer brake light does not work


Did yo check the fuse panel inside the truck its located on the drivers side dash , you have to open the driver side door, in there is a 10 amp fuse that is linked to rt trailer brakes and rt turn signal for the trailer, if the fuse is good there is a black box under the dash located on the floor on the driver side, just to the left of the break, thats where must of the plug in wire harness is for the trailer breaks!

May 31, 2009 | 2005 Chevrolet Silverado

2 Answers

Rear led brake light broke, replaced but new not working


YOU MIGHT WANT TO TRY TESTING THE TRAILER PLUG FUSE SOME OF THE THIRD BRAKE LIGHTS WORK OFF THAT FUNCTION. IF THAT DOES WORK TEST THE PLUG FOR POWER BEFORE THE PLUG, IF YOU HAVE POWER THAN IT IS IN THE PLUG, IF YOU DONT THAN CHANCES ARE IT IS IN THE FUSE BOX TEST ALL FUSES UNDER DASH AND UNDER THE HOOD.

May 20, 2009 | 2005 GMC Yukon Xl Denali

1 Answer

No brake lights on 96 yukon


The brake fuse #1 is located inside the truck below the steering column. I am assuming you have verified there is 12v power at the fuse & thru the brake lamp switch (orange wire power in & white wire power out, when pedal depressed) at all times. After the brake lamp switch , power goes (white wire) to the Turn signal/hazard lamp switch & out (dark green wire-rt brake lamp & yellow left brake lamp)

Feb 16, 2009 | 1999 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...