Question about 2005 Hummer H2

1 Answer

2005 H2 wipers run all the time and washer wont pump fluid? Wipers come on by themselves and work intermittently and stop mid window at any given time while the wiper switch is in the off position. Also will no longer pump windshield washer fluid?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I think my washer fluid pump may be frozen....where do I find teh washer fluid pump in my 2003 H2

Posted on Jan 27, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

When starting wipers came on and stay on no matter of position of control, washer fluid over head dome light won't turn on, rear washer and whiper won't work.


Wipers won't turn off......sometimes! - Ford Truck Enthusiasts Forums

www.ford-trucks.com > ... > Diesel > 6.7L Power Stroke Diesel
Feb 3, 2014 - Starting around 25,000 miles my wipers stayed on the slowest intermittent setting even when ... They only two that come to mind is the switch inside the cab or the wiper motor control board. ... The wipers do not park at the correctposition ... It doesn't really matter what steps need to be taken to fix the issue.

Window washer fluid put in window washer won't work now.

www.cargurus.com > Questions > Kia > Sorento

CarGurusAug 31, 2015 - Window washer fluid put in window washer won't work now. ... 4 answers. wipers working, not the washer though, pulled pump, intake screen clean. 2011 Kia Sorento Base ... Interior lights do not work when door is opened 7 answers. At first the back seat overhead light stopped working. Kia said it would ...

Nov 26, 2015 | 2011 Dodge Durango RT

1 Answer

Wipers stop in the middle of my wishield,will not park properly


Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jan 31, 2018 | 2005 Buick Century

1 Answer

During a recent snowstorm, the weight of the snow was apparently too much for the rear wiper. It stopped mid-stream and is stuck. Simultaneously, the intermittent function of the front wipers also quit. ...


Check fuse no. 11 (10A) in the driver's under dash fuse/relay box. I suspect it is blown. It provides power for the rear wiper, both washers, and the intermittent wiper function for front and rear. It probably blew when your rear wiper got stuck.

Jan 31, 2011 | 2003 Honda Odyssey

1 Answer

2005 h2 wipers run all the time


There was a recall on the suv`s but I`m not sure the h2`s were included.The fix was the replacement of the wiper motor module which is on the motor.All you have to do is remove the cover on the wiper motor and the module is there.Just unplug it and pry it out with a small screw driver.You can get a module from the dealership parts department.Just follow the directions.Hope this helps.Good luck.

Mar 23, 2010 | 2005 Hummer H2

1 Answer

I have a 2004 h2 hummer and my wipers and sprayer


they have a controll module afixed to the wiper motor itself. these modules have been an issue for gm for some time. they are very simple to replace and "usually" fix the issue.

Oct 25, 2009 | 2005 Hummer H2

1 Answer

2000 Jeep Cherokee Sport, window washing does not work


the little pump inside the washer fluid reservoir is bad, replace it

Dec 27, 2008 | 2000 Jeep Grand Cherokee

2 Answers

Hummer H2 rear wiper and sprayer came on by itself


It sounds like the wiper control module. The wipers on my 2003 did the same thing. After I pulled the fuse for the rear wiper, the front wipers started acting up as well. I had to pull fuses to stop them too. There is a recall on 2003 H2's for this issue. The cover of the wiper module on 2003s for the allows rain/water to get into the module. The cover will be replaced for free, however, in my case since the module was full of water and my wipers were not working, they replaced the module for free also. Not sure how much it would cost to replace on a 2005.

Dec 21, 2008 | 2005 Hummer H2

2 Answers

Repolacement fuse?


The fuse to your washer pump is shared with the wipers themselves. If your wipers work, then your pump should. I just had the same problem. You can replace the washer pump for $20. It's located behind the front passenger's side wheel well. Just remove the passenger wheel and wheel well covering to access the washer tank, and the motor. The pump pulls off, after removing the electrical plug and fluid line. When you pull the old pump out, the washer fluid will gush out. If you want to save any of this fluid, you may want to find a cloth or something to stop the flow. The new pumps snaps in quit easily.

Oct 18, 2008 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2005 Hummer H2 Logo

929 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...