Question about Kia Sorento LX

1 Answer

Need to reprogram the remote control to open the doors

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 111 Answers

Reprogramming will have to be done by the dealer.

Posted on Sep 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reprogram the garage door opener in the car


Put the opener remote near the buttons for the car system, with the key on hold both the remote open button down and the desired button on the car down for about 1 minute, that should program the system.

Jun 25, 2016 | 2010 Acura RDX

1 Answer

Remote not work cannot key open door


check the fuses or your remote battery went dead try replacing it. or your remote bacame deprogrammed and you`ll need to go to 1he dealer and have it reprogrammed. Usually $50 to $80

Mar 19, 2014 | 2005 Buick Century

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Remote entry only opens driver door


may be needed reprogramming the remote control

Aug 24, 2009 | 2004 Toyota Camry

1 Answer

I bought a G6 and the remote will not program to the car. i changed the batteries and went through the programing sequence several time and nothing happened. does anyone have any ideas?


The remote is probably bad - Take it to AutoZone and ask them to test the radio frequency of the remote. If it is bad you will need to get a new one - if not - remote control door lock receiver in vehicle is bad...and will need to be replaced and reprogrammed - you need to have special tools to reprogram the remote control door lock receiver.

Jul 17, 2009 | 2006 Pontiac G6

1 Answer

ALARM DON'T WORK WHEN ANY DOOR IS OPEN


There is a way to reprogram your remote but u will have to call the dealer

Jun 02, 2009 | 2001 Jeep Wrangler

1 Answer

Reprogramming remote and key


if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Mar 26, 2009 | 2004 Isuzu Rodeo

1 Answer

Need to reprogram door locks for 2004 Toyota Camry


I recently replaced the battery on my 2004 Toyota Camry. When I installed new battery the door locks will not stay unlocked once opened with remote. How do I reprogram?

Feb 21, 2009 | 2005 Toyota Camry Solara

2 Answers

Central locking not working on key.


Before you spend bigger amount, check the battery in the key. Usually a CR2032 battery can be find there. (Open the Keyfob by inserting an object into the key ring holder and pulling the top and bottom apart, Seperate the two halfs, Open the top half to expose the battery... )

Nov 28, 2008 | 1998 Audi A6

2 Answers

Door handle stuck


need to remove door panel either the linkage clip either broke or disconnected --if have remote start on fob need dealer to program--if normal try these links
Lexus Free Keyless Remote Fob Entry programming instructions Free Keyless Remote Fob Entry programming instructions procedures for all...

May 13, 2017 | 1998 Volvo V70

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...