Question about 2001 Chevrolet Venture

Open Question

Where is the pass through connector - 2001 Chevrolet Venture

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 dodge stratus 2.4L not passing emissions test why Emission saying Catalyst Not Ready Oxygen Sensor Not Ready I put 375 highway miles on the car, hopping this will pass it.


Again, TOO LITTLE INFO!!!

could be a non operating oxygen sensor heating, check connector and damaged wiring, as it is posible to damage wiring or connector at this very hot plecement. Amclaussen.

Sep 27, 2013 | 2004 Dodge Stratus

1 Answer

Coolant sensor is activating engine light


Sorry, you'll have to get it fixed correctly.
The warning light is on because the sensor is not working.
If the sensor is unplugged, the reading to the computer is 20 degrees below zero. If the connector is jumpered, the reading is 275 degrees.
Neither temp is within spec.

Feb 24, 2013 | Honda Cars & Trucks

1 Answer

Need to bypass passkey moduler


ohm your ignition key resistens and buy a resistor and place in connector under dash where steering column is, will have connector with to small wires, insert proper resistor in connector on eiring side not key lock side and that will by-pass pass key system

Sep 03, 2012 | 1991 Cadillac DeVille

1 Answer

On the dashboard a large red seatbelt symbol appears with the word pass underneath, also a large letter (i) appears next to the gauge


Did you transport a box or heavy object on the passenger seat?
The weight sensor (part of air bag system) detect a heavy object on the passenger seat.


With key on and engine running,clear the passenger seat ////// buckle then un-unbuckle to clear warning.

Also check the weight sensor and buckle connector.
Car wash clean can accident disconnect (or damage) this connector during vacuum.
======== Also inspect the pass. buckle opening for dirt.

Jul 28, 2011 | 2004 Saab 9-3

2 Answers

Ignition problem on 2000 olds intrigue


Are you seeing a check engine light ?

If, so the problem might be with crankshaft position sensor. You may have to get it replaced for $50-60

Jun 02, 2010 | 2000 Oldsmobile Intrigue

1 Answer

My 1969 chevelle's gas gauge is stuck pass full.bad gauge or sending unit? how to tell?


According to what I read, test the gauge first. Hook power to where the white wire attaches. Hook a ground to the black wire connector. The gauge should rise to full. (May take a while). When on full, the tan wire connector to same ground. It should go to empty. If both work, gauge is good. To test sender, in the empty position, your ohm meter should read 0-2. 1/2 tank should read about 40, and full should read 84-88 ohms.

May 17, 2010 | Cars & Trucks

1 Answer

Under My seat is a wire with yellow connector.


Probably for some sensor located in car seat telling computer that someone is seated there and possibly activating air bag circuit. Those bags are expensive and you do not want opening when not necessary.

Aug 31, 2017 | 1999 Ford Explorer

1 Answer

How do you set the timing on a 1994 Chevy Silverado 1/2 ton 4x4?


on the fire wall pass side or under the heater box along the carpet on the pass side there is a single wire connector you disconnect that.. is the spout timing connector .. that wil put the engine at base timing .. use timing light to see timing and turn the distributor after its loostened if nescessary to adjust it then retughten and turn off engine then reconnect the spout connector you disconnected earlier.. restart and it will be all set the code generated during the disconnection of the spout will not keep the engine light on once its been reconnected and engine restarted....

Feb 18, 2009 | 1994 Chevrolet C1500

1 Answer

Air Bag Light for passenger/Resistance high


passenger air bag resistance high caused by loose connection at psab connector. remove connector and twist pins slightly very slightly. connector is under pass seat and is yellow.

Feb 04, 2009 | 2001 Hyundai Sonata

1 Answer

Ignition Timing


How to check and adjust the timing
Disconnect the tan/black wire EST (electronic spark timing) by-pass connector located near the heater housing in the engine compartment on the S/T series, or near the distributor on all other V-6 models. Do not disconnect the four- (4) wire connector at distributor. Connect the timing light to the No. 1 spark plug wire. Check timing and adjust to "0" degrees BTDC. With the engine off, reconnect the EST by-pass connector and clear the ECM trouble codes by disconnecting the battery.

Aug 19, 2008 | 1991 Chevrolet Corvette

Not finding what you are looking for?
2001 Chevrolet Venture Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...