Question about 2003 Chevrolet Malibu

Open Question

Where is the crankshaft sensor on a 2003 chevy malibu

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: replace crankshaft sensor

Crank sensor on that car should be located near the pulley end of the motor, and near the firewall side. Fairly easy to get to.

Posted on Mar 06, 2009

Ad
  • 2039 Answers

SOURCE: Coolant Temp Sensor 03 Malibu

coolant sensor maybe 19 mm key its near the upper radiator hose in the engine thanks pierre

Posted on Dec 06, 2008

  • 260 Answers

SOURCE: horn not working chevy malibu

Check the fuse it may need replacing.

Posted on Apr 23, 2009

mechanicm639
  • 253 Answers

SOURCE: bad knock sensor on 1998 chevy malibu 2.4L

The knock sensor is on the back side of the engine near the trans. It is round, with a 1 wire connector. You will have to get it from underneath. Good Luck.

Posted on May 06, 2009

roniecon
  • 6826 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of a crankshaft sensor for a 2001 chev malibu


http://www.chevymalibuforum.com/forums/showthread.php?t=11860

Oct 04, 2014 | 2001 Chevrolet Malibu

2 Answers

Which crankshaft sensor drives the tach on 2003 Malibu


It is above and behind the Alternator on the top. It looks like a "D" battery standing-up with a female pigtail hook-up on the top of it.

Sep 19, 2014 | 2003 Chevrolet Malibu

1 Answer

2003 chevy malibu gas gauge always on empty, replaced the fuel pump


Need to replace the sensor inside the gas tank. I have a 2008 Malibu with the same problem. It was a faulty fuel gauge sensor.

Jan 31, 2012 | 2003 Chevrolet Malibu

1 Answer

I have a 2003 chevy malibu with 90,000 miles. i took it in for maintenance and the mechanic said that it was showing trouble code p0341. he said it was the cam sensor. yesterday when i went to start it, it...


if the cam sensor is bad, it will definitely not start. The cam shaft position sensor's function is: the engine speed and crankshaft position information is supplied frome a sensor which is usually situated at the front or rear of the crankshaft. note that distributor-located engine speed sensor are generally being replaced with crank shaft-located sensors,as worn disributor drives and associated components can effect the accuracy of the engine speed signal.

A camshaft position sensor,or cylinder identification sensor is used to determin the engine cycle position the information is used to provide individual cylinder ignition and injection cotrol.Many engine mangement systems use an inductive type of sensor that is located near the camshaft;when the camshaft rotates a single signal is passed to the ECU to indicate a reference point in the engine cycle

May 03, 2011 | 2003 Chevrolet Malibu

1 Answer

Where is the crank positioning sensor located on a 98 chevy malibu 4 cylinder


if a 2.2 four-cylinder, remove the starter motor. disconnect the 7x crankshaft position wiring and harness connector. remove crankshaft retaining bolt and withdraw sensor from engine block. replace the "O" ring and lightly lubricate it with new engine oil. installation is reverse of removal. have a good one !!

Oct 24, 2010 | 1998 Chevrolet Malibu

2 Answers

Were is the crankshaft position sensor located on 2001 chevy mali


It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Mar 22, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

IM a chevy Malibu 2003 My crankShaft Censor Keeps Burning out, 3times I have been to doctor (mechanic) they replace my sensor, Im good for a week then I burn out my crankshaft censor again and again what's...


One of two things. The sensor is being bumped or dropped before it is installed. Or the ECM has gone bad and it is putting out to much drive voltage for the sensors. I suspect that the sensor is being dropped or bumped before or during installation. These sensors are very fragile before they are put in. The sensor voltage from the ECM should be 5.0 volts +- .05 volts.
Thanks,
rich

Sep 26, 2009 | 2003 Chevrolet Malibu

Not finding what you are looking for?
2003 Chevrolet Malibu Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...