Question about 1991 Toyota Pickup

1 Answer

Hi I'm having an issue with my 1991 Toyota pick up truck 3.0 v6. I had the heads re-done and after the vehicle started it was making the loadest noise from the distributor hausing. It sounded as if I had no oil pressure, but when we checked we had plenty of oil pressure. Also the noise seems to get louder then all of a sudden the noise is gone. I pulled out the distributor but found no gears broken and or missing. Also at idle the check engine light is off, as soon as I drive a high RPM it turns on and the engine looses power. I set the timing at 10 degrees before top ded center. Can someone out there help out. Tony, Thanks!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Toyota Master
  • 1,062 Answers

You MIGHT have a vacuum leak which is affecting the timing.

Posted on Apr 09, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Toyota 1991 Pickup Truck V6 3.0 engine

i have a 92 with the same motor and 121k and it knocks too. so does my friends, i think they all dew. injector cleaner stopped his but then it started again

Posted on Nov 17, 2008

blueextc3221
  • 15935 Answers

SOURCE: 1993 V6 camry engine over heats and check engine light comes on

The thermostat housing is located by grabbing the upper radiator hose, and following it back to the engine block.
The housing that the hose is connected to is the thermostat housing.
Changing the thermostat will fix your problem!

Thanks for using FixYa - a FixYa rating is appreciated!!

Posted on Jan 31, 2009

tbirdfan1
  • 3051 Answers

SOURCE: Low oil pressure reading on ´96 Toyota T100

hi ben
my answer would be yes i would wory about it...
Guages are put on vehicals for a reason not just for looks i would have the car hooked to a diagnostic center and checked even though the guage may be faulty but i wouldnt take a chance

Posted on Feb 18, 2009

c17hydro
  • 2984 Answers

SOURCE: Hi,

What does it sound like?

Posted on Mar 11, 2009

pippall
  • 1486 Answers

SOURCE: 2003 Toyota Camry Se V6 has a check engine light

They may have disconnected the c o sensor.Check that first.If they haven't disconnected it.Change it and have the coeds cleared.Good luck

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1988 3.0. V6 4*4 toyota pickup the altanator is bad can I use an altanator off of a 1991 toyota ? Is it the sane?


If it will bolt up the same, has the same electrical plug on it and the same pulley then there shouldn't be an issue. All regular vehicle alternators basically have the same purpose and output. Good luck!

Nov 10, 2013 | Cars & Trucks

1 Answer

I have a 1991 Toyota body - V6- Automatic- Fuel injected- 21 foot RV that will not start, engine will not turn over no matter what I try. I have posted a couple of times, been given excellent suggestion...


Hi Tina, I am about 9000 miles from you and wonder if what I am going to suggest is what you probably have heard several times before. I can stand by here for about an hour if you have somebody to try my suggestions.
1) The battery - is it fully charged,
2) do any lights or the horn work
3) what happens when you turn the key to start
4) Do you her any clicking when the key is turned

Lets take it from here, I am standing by.

Apr 15, 2011 | 1991 Toyota Pickup

1 Answer

Hi i havea problem whit mi toyotacamry v6 it has spark but wont start andthe spark plug get so wet


sounds like a timing or carb issue.There are few different things that could be going on.

Feb 04, 2011 | 1991 Toyota Camry

1 Answer

Are the valves adjustable on the 1990 3.0L? I


1) The valves are adjustable, but they are of the shim-type adjustment. You will need to obtain the proper shims from a dealership parts department.

2) Any Toyota dealer can, by you giving them your VIN, tell you whatever was done to the vehicle under warranty

3) There are no special service campaigns for bed replacements, nor has there ever been one. Any bed that 'was' replaced was under factory "goodwill", to maintain customer satisfaction.

Oct 06, 2009 | 1991 Toyota Pickup

2 Answers

I want to replace my head gaskets, 91 v6 3.0 4x4 toyota. how bad of a job would it be? i know a little about cars but never done a head gasket.


It's a big job if you've never done one before. If you have and are familiar with this type of thing it should take about 8 - 10 hours. I strongly suggest that when you do you take the heads to a machine shop to check them over and HAVE THE VALVES ADJUSTED! They use pain in the neck shim system that has to be adjusted after 60? k otherwise you'll burn a valve.

Oct 01, 2009 | 1991 Toyota Pickup

1 Answer

My 1991 v6 4 runner auto has a flashing overdrive light on the dash. Most of the time it skips 2nd witch makes it sluggish. I plugged in a diagnostics link and get a fault message comming up on the...


That code 63= "Severed No. 2 solenoid or short circuit-severed wire harness or short circuit." There is a way to check the No. 2 transmission solenoid with an ohmeter. You'll have to disconnect the wire bundle from the ECT computer and measure the resistance between the S2 terminal and ground. You should see 11-15 ohms. If the solenoid is open or reads very high ohms, it should be replaced. This can be done by removing the transmission pan and the transmission oil filter to gain access to the solenoids. You do not need to remove the whole transmission from the vehicle.

May 13, 2009 | 1991 Toyota 4Runner

1 Answer

1991 toyota 4runner v6 auto rough start


Possibly a leaking head gasket. Water/antifreeze seeps into the cyllinder when it cools off, and then it won't fire properly until the coolant is blown out the exhaust when you start it. Let it warm up with the rad cap off. If you see bubbles continuously coming up to the filler hole, you have a head gasket problem. Do you have to add coolant monthly, or weekly?
If you're lucky, it could be just a spark plug that doesn't want to do anything until it warms up, or it could be a valve.

Mar 14, 2009 | 1991 Toyota 4Runner

1 Answer

1987 camry blows 30 amp fusible link when ign turned to on positi


Something is drawing too much power and you will have to find out which it is. When the head job was done they may have gotten a wire pinched in the block or some thing. You would have to be quite mknowledgable in vehicle electronics to find it. I would suggest that you take it back to the shop or guy that done the head job for you to correct.

Feb 12, 2009 | 1991 Toyota Camry

Not finding what you are looking for?
1991 Toyota Pickup Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...