Question about 2006 Ford F 350 Super Duty

1 Answer

2006 ford e350 6.0 liter died on road, cranks but will not start. checked crank censor, vss, electronic fan, batteries,powers and ground, fuel system,cleaned connection on pcm,checked oil pressure(good). HELP

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It was you ficm . i know because it happend to me . get a used ficm of ebay and your truck will strart right up . also on the e series it is located on the left fender , not the valve cover

Posted on Jul 21, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
kayzack519
  • 226 Answers

SOURCE: i have a 2005 jeep

neutral safety switch is on the side of the transmission and a very common problem with chrysler vehicles.This is a picture of what your looking for(this would be facing the transmission) but it gives you a general idea. Its 32.00 at jcwhitney.com




g_30584g_cl_1.jpg

Posted on May 21, 2011

  • 14036 Answers

SOURCE: my buick regal doesnt send signal from pcm to crank relay.

check pcm with a scanner to see if crank and cam sensor are working.

Posted on Apr 17, 2009

cincinaty5
  • 132 Answers

SOURCE: 2003 Dodge Caravan 3.3 No Crank, No Start

replace the neutral safty switch

Posted on Aug 28, 2009

  • 90 Answers

SOURCE: pcm is not grounding injectors. need a pin diagram and ground location diagram

Ground points are in different locations throughout wiring harness. If you had any work done to engine it is very possible to have missed one of the grounding eyelets during the process of putting things together. Check along wiring harness in any area you can see or reach to try to locate any loose or disconnected ground looks.

Posted on Nov 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced head gaskets on 2002 aztek i started it with charger on disconnected charger it died . now wont start got fuel at rail got spark security light never comes on


Sounds like the battery is dead and the alternator is not putting out power. The truck runs off the alternator after it starts. The battery is just there to start the truck. Try to jump start the truck again and once it is running take the positive cable off the battery and if it stops running you have a problem with the alternator.

Jun 09, 2017 | Cars & Trucks

1 Answer

1998 Ford Explorer. 4.0 liter. SOHC Good fuel pressure. & good fire on plugs. Changed crankshaft sensor . Still wont crank, No fuel is getting thru the Injectors.


check for a problem cam shaft censor as well as a crank position sensor as both are required to be operational for the ECM to start the engine

Jun 25, 2016 | 1998 Ford Explorer

1 Answer

I have aa 2007 chev her with 2.22 liter some of the fuses don't get power and some do on the fuse box block under hood everything to start and run car is dead


2007 Chevy her ? HHR ? 2.2L 4cylinder , check the run/crank relay ! Relay # 51 in the under hood fuse/relay box.
Power to many of this vehicle?€™s circuits are controlled by the module that is designated the power mode master (PMM). This vehicle?€™s PMM is the body control module (BCM). The PMM controls which power mode (Run, Accessory, Crank, Retained Accessory Power, or Off) is active.
Run/Crank Relay The run/crank relay control circuit is connected to a constant ground and is switched by the ignition 1 circuit or the body control module (BCM). The BCM, will in lieu of the ignition switch position, activate the Run/Crank relay during a remote start event. The Run/Crank relay supplies a power signal to the following circuits, when the a Run or Crank power mode is selected:
?€¢
Automatic transmission shift indicator


?€¢
Automatic transmission (A/T)


?€¢
Switched power feeds to the BCM


?€¢
Electronic brake control module (EBCM)


?€¢
Electronic ignition module (spark control)


?€¢
Electronic power steering module (EPS)


?€¢
Fuel injectors


?€¢
Powertrain control module (PCM)


?€¢
Park neutral position (PNP) switch

Dec 22, 2015 | Cars & Trucks

2 Answers

94 ford ranger splash 4.0 will start but dies,i don't know if it is fuel related or what. iv'e changed about everything I know.


Try the ignition module or the ignition switch itself. I have seen them before where they will only get spark in the crank mode. Also check and make sure that your wires are on the correct side of the starter solenoid and not only getting power when you are cranking.

Oct 10, 2015 | Ford Cars & Trucks

1 Answer

02 Ford Escape V6 4X4 died while driving and now cranks but no start.


did you check if you got a timing belt because sound like a timing belt broken. good luck

Sep 17, 2014 | 2002 Ford Escape

2 Answers

Drove it about 26 miles shut it off for about 30 min. got back in to start it turned the key it started and died then it wouldnt start again


Have you checked to see if the fuel pump is getting power from the relay and if the pump is producing fuel pressure ?

Apr 08, 2014 | 2006 Chrysler Town & Country

1 Answer

89 camery no start , has fuel p.s.i. , injectors fireing , spark on all plugs , compression even across


Have you checked cam timing?If it has jumped a tooth or two it will not start.

Jun 18, 2017 | 1989 Toyota Camry

1 Answer

2006 Liberty: My 2006 jeep liberty dies while driving and won't ...


Most common causes of that kind of problem are the fuel pump and the crank sensor. Crank sensor should set a code, pump won't. Less frequent but worth mentioning is the ignition switch. Do some testing using a haynes or chilton manual as a guide,. All you need for that is a digital multi-meter.
Before testing anything, check that all the ground points under the hood are clean and secure. there are more than just the battery to the block...check all the smaller ones as well.

May 05, 2010 | 2006 Jeep Liberty

1 Answer

2008 Ford F150 5.4 Stalled going down road and now will only crank for a second then stops cranking. Battery good. Fuel inertia good. If it is the fuel pump, would it not keep cranking?????


Yes, you are right,it will still crank with a bad fuel pump. It sounds like a bad battery cable. Check all connections, especially the ground. A bad connection or cable at the negative end would shut down the processor and cause the cranking problem at the same time. This is the only thing I can think of that would cause both at once, unless you have two different problems that happened to show up at the same time.

Sep 21, 2009 | 2004 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...