Question about 1989 Buick Skyhawk

Open Question

Where is located crankshaft sensor on engine block for Buick Skyhawk 1989? Thanks, Mike.

Posted by on

  • yadayada
    yadayada Sep 16, 2010

    front of the crank near the pulley

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 169 Answers

SOURCE: buick regal 1996 crankshaft position sensor

IF THE CRANK SENSOR GOES BAD ON THAT ENGINE THE CAR WILL STOP RUNNING OR NOT START IF TRYING TO START IT. NEED THE CODE INFO TO HELP YOU FURTHER. TRY GOING TO ADVANCED TO GET THEM TO READ THE CODE-THEY DO THIS FOR FREE.

Posted on Aug 26, 2008

HGComputers
  • 81 Answers

SOURCE: Crankshaft positioning sensor location?

After you take the plastic cover off the engine, and remove the valve cover breather tube, place a light under the two rubber brake hoses shining foward. Between the valve cover and the throttle chamber look straight down toward the ground see a plug and black sensor with green release held to the engine block with a gold colored 10mm hex headed bolt. There it is. Take your time. Ask if you need anything else. Hope it helped.

Posted on Jan 04, 2009

csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many crankshaft position sensors are on a 1998 buick century 3100 engine and locations


Two crankshaft position sensors .
Crankshaft Position (CKP) Sensor (7X)
Lower rear of the engine block, below the exhaust manifold

Crankshaft Position (CKP) Sensor (24X)
Right side of the engine, at the end of the crankshaft, behind the harmonic balancer

Jul 10, 2017 | Buick Cars & Trucks

1 Answer

Where is the crankshaft sensor located on my 1998 Buick skylark 6 cylinder


Which one ? Your vehicle has two .
24X Crankshaft Position (CKP) Sensor
Front of engine behind the harmonic balancer !
7X Crankshaft Position (CKP) Sensor
Right front side of engine in the engine block
Crankshaft Position Sensor Replacement (24X CKP Sensor)
Tools Required J 29113 Crankshaft Pulley Hub Puller

Oct 26, 2015 | Buick Cars & Trucks

1 Answer

Where is the crankshaft position sensor located on a 2002 Buick Century 3100?


There are two crankshaft sensors on this engine. One is hidden behind the harmonic balancer, and the other is in the side of the block. Here are pictures of the each sensor and where they are.

25920440-exy5s5hsyc0am45rwd43e5df-5-0.jpg

25920440-exy5s5hsyc0am45rwd43e5df-5-1.jpg

25920440-exy5s5hsyc0am45rwd43e5df-5-3.gif

25920440-exy5s5hsyc0am45rwd43e5df-5-6.gif

Oct 23, 2015 | Buick Cars & Trucks

1 Answer

Have a 1989 Buick Skyhawk and it is dying alot and sputters. Changed the fuel filter still won't drive more than a block sputters and dies. Can you recommend a good mechanic in Casper, WY


FIRST CHANGFE YOU TPS (THROTTLE POSITION SENSOR) LOC. ON SIDE OF THE THROTTLE BODY SKYHAWS USUALLY NHAVE THIS PROB. WHEN THE MILIAGE GETS OVER 100,000 MILES.

Aug 14, 2011 | 1989 Buick Skyhawk

2 Answers

Where is the cam shaft sensor


Hello,

The crankshaft position sensor on a 1989 Oldsmobile Cutlass Ciera is located inside the engine compartment. On the Ciera's bottom of the engine block is the oil pan. The crankshaft sensor is on the side of the oil pan.

Take care.

Sep 03, 2010 | 1989 Oldsmobile Cutlass Ciera

2 Answers

Where is crankshaft sensor located on a 1989 pontiac grand prix with a 2.8l v6


Will be on the side of the engine block.Held on with one bolt that screw into the block, remove bolt and sensor slide out.

Jun 18, 2010 | 1989 Pontiac Grand Prix

1 Answer

Where is the Cam Sensor located on a 1995 Buick Century 6cyl engine? Is it accessible for replacement?


Under hood, passenger side, lower engine area, above and behind crankshaft pulley, mounted on engine block.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Jul 01, 2009 | 1995 Buick Century

2 Answers

My 1989 buick regal wont start trys but wont changed coils no spark need help


COULD BE THE CRANKSHAFT POSITION SENSOR. LOCATED ON THE BACK SIDE OF THE ENGINE NEAR THE FREEZE PLUGS. I HAVE HAD A SIMILAR PROBLEM AND THIS SHOULD FIX IT. YOU WILL NEED AN 8MM WRENCH TO REMOVE THE BOLTS THAT HOLD IT IN PLACE. BEST OF LUCK. KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA.

May 10, 2009 | 1989 Buick Regal

1 Answer

Crank sensor


The crankshaft position sensor is located on the right side of the engine block.
moz-screenshot.jpgTypical DIS Crankshaft Sensor 41844070

Dec 21, 2008 | 1990 Buick Regal

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...