Question about 2000 Jeep Grand Cherokee

Open Question

How do I disable stock alarm on a 2000 grand Cherokee?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Mikey108
  • 475 Answers

SOURCE: ALARMS

Insert key into drivers door lock and turn the key to unlock

Posted on Nov 19, 2008

Ad
Mikey108
  • 475 Answers

SOURCE: jeep grand cherokee 2000 3.1 td alarm indicator light situated on dashboard

If this is an after market alarm it could have been turned off.

Posted on Oct 22, 2008

walt36
  • 4 Answers

SOURCE: 1999 JEEP GRAND CHEROKEE LAREDO

i have a 95 jeep grand cherokee lerado from time to time my alarm goes off i dont have a remote 4 my alarm but i found out that if you put the key in the driver door and unlock it. it will reset the alarm!!!!!

Posted on Dec 12, 2008

  • 1 Answer

SOURCE: alarm wont disarm and unlocking doors does not work any suggestions?

I just had the same problem with my 1995.. believe me its a pain! by the way on the driver side below the steering wheel close to the door there should be a hidden pink (or any color) plastic box which basically controlls the cars security system... i removed it and i was good to go...try that... the only thing though is that you wont be able to lock the doors automaticaly, ull have to do it manually

Posted on May 22, 2009

bestdarngood
  • 3037 Answers

SOURCE: 1995 Jeep Grand Cherokee Laredo Alarm system

You could also pull the plug from the factory alarm control module thus taking it totally out of the system. It is behind the glove box (the furthest module on the left... attached with 2 screws. It seems like a PITA job, but it is really not too bad if you have a phillips head screwdriver and about 45 mins to 1 hour.

You will need to remove the dash, the radio/center console bezel, and then finally you can get to the glove box. I'll give you the rundown if you want to go this route.

First, you will need to remove the screws holding the front of the dashpad down. There are 3 screws along the top of the bezel around the instrument cluster, 2 screws along the top of the radio/center console bezel, and 2 screws along the top of the inside of the glove box.

Next, gently pry the center defrost bezel (along the back of the dash pad near the winshield - be careful, mine has two sensors attached: auto headlights and the temperature). Once that is removed unhook the two sensors and remove the defrost bezel.

Underneath the defrost bezel you will find 4 screws holding the dash down, remove those. Now you have removed all the screws holding your dash in place. In order to make it easier to lift the dash out of the car, you might want to remove the side pillar trim pieces (they are the plastic pieces that run from the dash to the headliner on both sides). They are held on by two metal 'snap-type' fittings, so you just need to genly pull on them and they will separate. Now, the only thing holding your dash in place are two 'snap type' fittings one on the forward drivers side edge and one on the forward passengers side edge. Genlty pull up on the dash in these areas and they will separate. Now you can remove the dash. (It sounds like a lot of work, but it took me longer to type this than actually doing it).

Once the dash is off, you will need to remove the radio/center console bezel. This is held on by 6 screws (2 of which you already removed). Remove the middle two screws, and then remove the ash tray to uncover the bottom two screws. Remove those and you can gently pry out the bezel. There is will be a connection for the cigarette lighter - you can unplug or just simply move the bezel out of the way slightly. The only reason to remove this is so that you can uncover one of the screws holding the glove box on.

Now you are finally ready to remove the glove box. First pull of the fuse panel cover door and the side demister boot (rectangular black thing above the fuse panel - just snaps in place, so pull gently to remove). Now open the glove box and remove the 3 screws along the front that hold the relay cover in place. You can remove that piece and set it aside. Next remove the four screws along the underside of the glove box (when looking up from the passenger side floor). Then remove the screw along the left edge of the glove box - lower left corner (the one that was hidden by the radio/console bezel). Now, there are 4 screws along the top that were hidden by the dash (the whole reason you had to pull the dash). Remove those and you can pull the glove box. There is a connection for the light - unhook that and you can take the whole glove box out and set aside.

Now to find the alarm relay. When looking at the cavity behind the glove box you should see some relays (turn signal, hazard, etc) that would normally be accessed by removing the cover inside the glove box. These are on the right side. In the center there will be a box that is approximately the size of a pack of cigarettes mounted by two screws. You will need to remove those screws and pull that box out of the way. The alarm module is the next cigarette size box to the left. It is mounted partly behind the plastic that makes up the front edge of the cavity by two screws. Remove those screws and you can pull the alarm module out. It has a 16 pin (I'm pretty sure) connector that you can unplug. That should totally remove the alarm from your system.

Let me know if you need any further help, good luck

Posted on May 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Disable factory security systen on a jeep grand cherokee 2001


why not say what security system? there are many
alarm
immobilizer (skim,skis, )_
radio
nav
what?
tell what you dont like, and we can tell what you mean.

the alarmh as a disable mode... if that is your drift...\\
the oper guide covers that. and answered here 100s of times.

the IMMO is not hackable, sorry.
93-98' yes. , not 2001

Aug 20, 2015 | 2000 Jeep Grand Cherokee

1 Answer

Why does the alarm on my 2000 jeep grand cherokee not go off when the lift gate is opened


Hi Gloria, I'm glad to help!

Gloria, the most likely cause for no alarm when the liftgate is opened is usually because the controller does not see the liftgate open. 2 things can cause this. (1) The alarm switch on the liftgate could be bad. (2) The wiring going to the switch could be broken somewhere in the wiring. On the Jeeps its usually broken where the wiring is bending all the time between the liftgate and the body of the vehicle. If you pull the rubber insulator out you can then check the wiring. If the wiring is good then the next step would be to try an alarm switch for the liftgate. Hope this helps and have an awesome day Gloria.

Sep 06, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Disable factory alarm 2000 jeep cherokee


no solution just a question say i have two 2000 jeep grand cherokees
being cheap and not sure if the one even works I was going to take the module out of the one i know works out of the donor jeep and install in in the cleaner limited jeep but where is the keyless module installed in these trucks

Jul 25, 2012 | 2000 Jeep Grand Cherokee

1 Answer

I have a 1993 jeep Cherokee and the alarm is going off and i can't start the car.


If it's not a factory alarm locate the alarm unit and the main power line running to that alarm and remove the in line fuse from that line. That will disable the alarm and should disable the starter kill switch that is installed.

Sep 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Need to un-hook alarm.


If it is a factory alarm, you can have your anti theft disabled at the dealership.

Jul 16, 2009 | 2000 Jeep Grand Cherokee

1 Answer

ALARMS


Insert key into drivers door lock and turn the key to unlock

Nov 19, 2008 | 1999 Jeep Grand Cherokee

3 Answers

1999 JEEP GRAND CHEROKEE LAREDO


i have a 95 jeep grand cherokee lerado from time to time my alarm goes off i dont have a remote 4 my alarm but i found out that if you put the key in the driver door and unlock it. it will reset the alarm!!!!!

Nov 19, 2008 | 1995 Jeep Grand Cherokee

1 Answer

Jeep grand cherokee 2000 3.1 td alarm indicator light situated on dashboard


If this is an after market alarm it could have been turned off.

Jun 20, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

1,081 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...