Question about 1966 Ford Mustang

Open Question

Ignition harness Steering column wiring 1973 ford mustang

Trying to replace the wiring in my 73 ford.Need to know what wire goes where on the ignition harness that comes off of the steering column.(Not the directional switch)

Posted by on

6 Suggested Answers

Ajkill
  • 2035 Answers

SOURCE: steering column

  1. Set the parking brake.
  2. Disconnect the battery ground cable.
  3. Unbolt the intermediate shaft from the steering column.
  4. Disconnect the shift linkage rod(s) from the column.
  5. Remove the steering wheel.
If you have a tilt column, the steering wheel MUST be in the full UP position when it is removed.
  1. Remove the floor cover screws at the base of the column.
  2. Remove the steering column shroud by place the bottom screw in the No.1 position and pulling the shroud up and away from the column.
  3. On automatics, remove the shift indicator cable.
  4. Remove the instrument panel column opening cover.
  5. Remove the bolts securing the column support bracket to the pedal support bracket.
  6. Disconnect the turn signal/hazard warning harness and the ignition switch harness.
  7. Lift the column from the vehicle.
  8. Remove the column support bracket
To install:
  1. Install the column support bracket making sure that the wiring is outboard of the column. Torque the nuts to the specifications shown in the Torque Chart at the end of this Section.
  2. Start the floor cover clamp bolt and press the plate until the clamp flats touch the stops on the column outer tube.
  3. Install the column through the floor opening.
  4. Connect the turn signal/hazard warning and ignition harnesses.
  5. Raise the column and install the 2 support bolts.
  6. Tighten the floor cover bolts to the specifications shown in the Torque Chart at the end of this Section.
  7. Torque the support bracket bolts to the specifications shown in the Torque Chart at the end of this Section.
  8. Torque the cover plate clamp bolt to the specifications shown in the Torque Chart at the end of this Section.
  9. Install and adjust the shift indicator cable, on automatics.
  10. Install the instrument panel column opening cover.
  11. Install the column shroud.
  12. Torque the shroud bottom screw to 15 inch lbs.
  13. Connect the shifter rod(s).
  14. Connect the intermediate shaft. Torque the bolt to the specifications shown in the Torque Chart at the end of this Section.
Good luck...

Posted on Nov 01, 2008

bunnydawg
  • 5158 Answers

SOURCE: Need engine wiring diagram for Ford Mustang 95 cobra 302 engine

http://www.veryuseful.com/mustang/tech/engine/

Posted on Mar 07, 2009

localwonder
  • 6784 Answers

SOURCE: Replacing the ignition switch in a 96 ford mustang cobra svt

Follow these steps carefully. this will help you achieve this replacement.



  1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

  2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

  3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

  4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

  5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

  6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Posted on Jun 17, 2009

  • 164 Answers

SOURCE: replace ignition in steering column 92 jeep laredo

dealer has better picture they can print out for you give them a call

Posted on Jul 26, 2009

CMV9
  • 594 Answers

SOURCE: How do I remove the ignition lock cylinder from

here are the instruction the first set are the instruction on how to remove the turn signal switch as you will need them to remove the ignition

Removal & Installataion of turn signal switch

  1. Disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Loosen the anti-theft cover retaining screws on 1976 models and lift the cover from the steering column. It is not necessary to completely remove these screws.
  4. Depress the lockplate and pry the round wire snapring from the steering shaft groove. A lockplate compressor tool is available for compressing the lockplate.
  5. Remove the lockplate, directional signal canceling cam, upper bearing preload spring, and thrust washer from the steering shaft.
  6. Move the directional signal actuating lever to the right turn position and remove the lever.
  7. Depress the hazard warning light switch and remove the button by turning it counterclockwise.
  8. Remove the directional signal wiring harness connector block from its mounting bracket on the right side of the lower column.
  9. On vehicles equipped with an automatic transmission, use a stiff wire, such as a paper clip, to depress the lock tab which retains the shift quadrant light wire in the connector block.
  10. Remove the directional signal switch retaining screws and pull the switch and wiring harness from the steering column.
  11. Guide the wiring harness of the new switch into position and carefully align the switch assembly. make sure that the actuating lever pivot is correctly aligned and seated in the upper housing pivot boss prior to installing the retaining screws.
  12. Install the directional signal lever and actuate the directional signal switch to assure correct operation.
  13. Place the thrust washer, spring, and directional signal canceling cam on the upper end of the steering shaft.
  14. Align the lockplate splines with the steering shaft splines and place the lockplate in position with the directional signal canceling cam shaft protruding through the dogleg opening in the lockplate.
  15. Install the snapring.
  16. Install the anti-theft cover.
  17. Install the steering wheel and connect the negative battery cable.
  18. Check the operation of the turn signal switch.

Removal & Installation of ignition lock switch
  1. Disconnect the battery ground cable.
  2. Remove the turn signal switch as described earlier in this section. You don't have to remove the switch completely, just set it aside.
  3. Insert the key. Position the key as follows.
    • 1976-83: With manual transmission, put it in the ON position; with automatic, put it in OFF/LOCK.
    • 1984-86: Two detent positions, clockwise, beyond OFF/LOCK.
  1. Working through the slot next to the turn signal switch mounting boss, use a thin screwdriver to release the lock cylinder.
  2. To install, insert the key in the new lock cylinder. Hold the sleeve and turn the key clockwise until it stops. Align the cylinder retaining tab with the housing slot and insert the cylinder. Push the cylinder in, rotate to engage, then push in until the retaining tab engages the housing groove.
  3. Complete the procedure in the reverse of removal.

Posted on Aug 20, 2009

  • 2 Answers

SOURCE: wiring diagram or color chart for a 96 ford mustang radio harness

dont even worrie about it just go to walmart or an auto parts and get a wiring harness they are not so expensive

Posted on Sep 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steering column wiring


there are many unused wires on nearly all wiring harnesses as they are usaully used on many different models and makes if everything is working don't let it worry you

Mar 28, 2014 | 1994 Ford Ranger Supercab

1 Answer

How to replace ignition lock cylinder


This may or may not help,but i found this

REMOVE OR DISCONNECT

1. Disable the SIR System.
2. Battery negative cable.
3. Knee bolster and IP steering column reinforcement. NOTICE: The steering column should never be supported by only the lower support bracket alone, damage to the column lower bearing adapter could result.
4. Lower support bracket from vehicle (2 bolts).
5. Upper column support from IP (2 bolts).
6. Lower steering column so that it rests on the driver seat.
7. Ignition switch wiring protector.
8. Ignition switch retaining screw and nut.
9. Ignition and turn signal switch column harness connectors from IP harness.
10. Turn signal switch connector from column harness.
11. Ignition switch, harness, and connector. Important

o DO NOT splice ignition switch wires.

INSTALL OR CONNECT

1. Ignition switch, securing with retaining screws.

o Adjust ignition switch. Steering Column Unit Repair.

2. Turn signal switch connector to column harness.
3. Ignition and turn signal switch column harness connectors to IP harness.
4. Ignition switch wiring protector.
5. Raise steering column to support bracket.
6. Two bolts to upper support bracket. Do not tighten fully at this time.
7. Bolt and nut to lower support bracket.

o Align column to instrument panel opening. A small shim (wedge) placed between the instrument panel column support bracket and the column can be used to hold the column stationary while tightening the upper support bolts.
o Upper and lower column support bolts and nuts to 27 Nm (20 ft. lbs.).

8. IP steering column reinforcement plate and knee bolster.
9. Battery negative cable.
10. Enable the SIR system.
super vag k+can v4.8

Jul 30, 2012 | 1994 Geo Prizm

1 Answer

I have an 86 mustang 5.0 .When I turn the key to the on position, the warning lights in dash do not cycle as they should.I replaced the ignition cylinder, no such luck... Any ideas out there????


If your fuses are good, and no loose wires, try the ignition switch, not lock cylinder, the ignition switch is located on the steering column about two-three inches away from the ignition lock cylinder towards the dash on the steering column.

Feb 10, 2011 | 1986 Ford Mustang

1 Answer

Need to know how to hot wire ignition.what color wires do i use?


1991 Ford F150

Vehicle Battery Positive Wire (+): Yellow
Vehicle Battery Positive Wire Location: Ignition Switch Harness
Vehicle Ignition Wire (+): Red/Light Green
Vehicle Ignition Wire Location: Ignition Switch Harness
Vehicle Second Ignition Wire (+): N/A
Vehicle Second Ignition Wire Location: N/A
Vehicle Accessory Wire (+): Gray/Yellow
Vehicle Accessory Wire Location: Ignition Switch Harness
Vehicle Second Accessory Wire (+): N/A
Vehicle Second Accessory Wire Location: N/A
Automobile Engine Starter Wire (+): Red/Light Blue
Automobile Engine Starter Wire Location: Ignition Switch Harness
Automobile Second Engine Starter Wire (-): N/A
Automobile Second Engine Starter Wire Location: N/A
Factory Anti-Theft System: None
Factory Anti-Theft System Type: None
Car Key Sense Wire (-): Black/Pink
Car Key Sense Wire Location: At Steering Column Harness
Car Neutral Safety Wire (+): N/A
Car Neutral Safety Wire Location: N/A
Car Tachometer Wire (-): Tan/Yellow
Car Tachometer Wire Location: At Ignition Switch Control Module in Driver Fender Well
Car Speed Sense Wire: Gray/Black
Car Speed Sense Wire Location: Pin #3 at PCM Mounted on the Firewall
Car Parking Lights Wire (+): Brown
Car Parking Lights Wire Location: At Headlight Switch or Driver Side Kick Panel
Car Brake Lights Wire (+): Green
Car Brake Lights Wire Location: At Brake Switch Above the Pedal
Car Reverse Lights Wire (+): Black/Pink
Car Reverse Lights Wire Location: At Switch on Transmission
Car Horn Wire (-): Blue
Car Horn Wire Location: At Steering Column Harness

Sorry friend, this is as far as i can go to tel you how to hot wire the ignition. But with the color codes you should be able to figure it out, Good luck and keep me posted.

Jan 23, 2010 | 1991 Ford F150

1 Answer

I am trying to change the ignition switch in my 91 chevrolet truck and i cant get the old switch out.


f
The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.

78b188a.gif

The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.

Good luck (remember rated this help)

Jan 05, 2010 | 1991 Chevrolet C1500

1 Answer

Need to know how to remove and replace my f 150 ingention it is a 1987 and what tools i will need


The ignition switch is usually mounted to the steering column and is operated by a linkage rod.
NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.
The ignition switch is operated by the key switch. Courtesy of Ford Motor Company.
To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.
a4d28fb.gif

Oct 22, 2009 | 1987 Ford F 150

1 Answer

WE HAVE A 67 MUSTANG AND WE BOUGHT A NEW TURN SIGNAL SWITCH TO REPLACE AND NEED TO KNOW HOW TO INSTALL IT AND MATCH THE WIRING IN THE STEERING WHEEL , COULD YOU PLEASE EMAIL ME A STEP BY STEP INSTRUCTIONS...


You will need to remove the steering wheel from the post with a puller. Once you find the switch inside remove anything in your way and make note of where it goes. There are usually three screws holding the switch in. Once free, you need to unplug the lower harness connector and thread it up through the column. Match the wiring on the old switch to that on the new one. If the new one has a connector is identical and wires match, use it as is. If the connector or wiring is different, match each wire, starting at the switch location and place that wire in position in the connector. It helps to write down each location both at the switch and connector so if you get lost in the middle you can have a reference to go back to.
Once wiring is correct, thread the connector and harness back down through the column and finish putting it back together.
I would check operation before putting wheel back on. Also it helps to mark the wheel position to the shaft so it does not end up being uneven and not centered.(do that before takingwheel off) Also don't hammer on shaft to get wheel off definitely use a puller.

Oct 01, 2009 | 1966 Ford Mustang

1 Answer

How do I replace the ignition switch in my 1992 explorer


hi,
Remove the steering column cover. There should be four screws. This will give you access to the column and the switch located behind the ignition lock cylinder.Unplug the wiring harness from behind the ignition switch. The wiring harness snaps into the switch.Unscrew the two screws that are holding the switch in place. The switch will lift right out.Replace with the new switch. The OEM part should fit perfectly in the same spot.Tighten the screws down to lock the new switch into place.Fasten the wiring harness to the back of the switch.
Reassemble your steering column. Tighten the screws.Crank your Ford Explorer to test if the ignition switch was definitely the problem. The truck should run smoothly with no stalls or missed cranks.

thank you for using fixya,rate my answer
vijay

Oct 01, 2009 | 1992 Ford Explorer

1 Answer

Looking for a 1967 mustang steering column wiring diagram


Check out CJ Pony Parts for replacement turn signal/horn wiring harnesses. Try www.hammar.dyndns.org - he has some wiring diagrams (called schematics)

Jul 11, 2009 | 1966 Ford Mustang

1 Answer

Replacing the ignition switch in a 96 ford mustang cobra svt


Follow these steps carefully. this will help you achieve this replacement.



  1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

  2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

  3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

  4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

  5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

  6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Jun 17, 2009 | 1996 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...