Question about 1986 Lincoln Mark VII

Open Question

How to replace the starter on A 1986 lincoln lsc I am having a challenge getting the top bolt out

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jmeredith
  • 417 Answers

SOURCE: starter

hi,

take off the passenger side front tire and youll have to use a couple of socket extensions to get it, make sure to jack and block car correctly. when you remove the tire you should be able to see the top bolt with a droplight through the wheelwell
access is through the wheelwell I believe.

J

Posted on Sep 07, 2008

SOURCE: 1995 (X300) Jaguar XJ6 Starter Replacement

Remove the windshield wiper motor for access to the top bolt. Use a 13mm dogbone with a pipe or similar for leverage.They used locktite on the bolts,so it's a bear to get loose. This job is a real P.I.T.A. Good luck.

Posted on Apr 07, 2009

  • 35 Answers

SOURCE: Reaching top starter bolt.....

Easiest way I have done this is by reomving the rubber intake pipe. Then by using a 14mm flex socket with a 6 inch extension. You may also have to remove the starter to give yourself a little bit more room.

Posted on Apr 17, 2009

  • 50 Answers

SOURCE: i'm replacing the starter in my 97 Lincoln

Look for the third bolt on the top of the starter. It may have to be accessed past the engine mount with a long extension.

Posted on Jul 04, 2009

canbruce75
  • 1776 Answers

SOURCE: Need to replace starter on a 1986 Camaro.

Removing the starter

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect all wiring from the starter solenoid. Replace each nut as the connector is removed (as thread sizes differ from connector to connector). Note or tag the wiring positions for installation.
  4. Remove the bracket from the starter and the two mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.
  5. Remove the front bracket bolt or nut. Lower the starter front end first, and then remove the unit from the car.
These are the steps for removing the starter on the Camaro. Did you remove the bracket? Hope this helped and best wishes.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a1989 Lincoln vii lsc and I need to know where the starter is located and how much a replace one. rebuilt


STARTER UNDERNEATH CAR LOOK WHERE FLYWHEEL LOCATED YOU WILL SEE STARTER AT FLY WHEEL COVER. STARTERS CAN COST FROM $100.00 OR LITTLE MORE.BUT CALL AROUND GET A PRICE CHECK.

May 18, 2011 | Lincoln Mark VII Cars & Trucks

1 Answer

Wish to know how many hp i have? how do i tell if it is a later year model?


Several variations of the 5.0l V8 for the Lincoln 1987 Mark VII. 150 hp (112 kW), (112 kW) 270 ft-lbf SEFI (1986-1987) w/ AOD 4 Speed Automatic.
200 hp (149 kW) SEFI 285 (ft lbs)(1986-1987 LSC) w/ AOD 4 Speed Automatic
225 hp (168 kW) 300 lbf.ft (407 Nm) SEFI (1988 - 1992 ALL) w/ AOD 4 Speed Automatic
Thank you for using Fixya and hope this helps you.

Mar 25, 2010 | 1987 Lincoln Mark VII

1 Answer

Need to replace starter on a 1986 Camaro, but cannot get the old starter past the exhaust pipe.


Removing the starter
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect all wiring from the starter solenoid. Replace each nut as the connector is removed (as thread sizes differ from connector to connector). Note or tag the wiring positions for installation.
  4. Remove the bracket from the starter and the two mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.
  5. Remove the front bracket bolt or nut. Lower the starter front end first, and then remove the unit from the car.
These are the steps for removing the starter on the Camaro. Did you remove the bracket? Hope this helped and best wishes.

Aug 01, 2009 | 1986 Chevrolet Camaro

1 Answer

I'm replacing the starter in my 97 Lincoln Continental. I have the two bolts out and it will not budge. What do i have to do to get it off? Thanks!!!


Look for the third bolt on the top of the starter. It may have to be accessed past the engine mount with a long extension.

Jun 30, 2009 | 1997 Lincoln Continental

1 Answer

1991 lincoln mark vii lsc runs but not when let the key go back t


its the ignition switch. inside the steering column. at the local parts store. not to expensive part. good luck

Mar 12, 2009 | 1991 Lincoln Mark VII

2 Answers

Removing the starter from a 1996 lincoln town car


i had 1 done and let me just say 2 bolts are very easy but that dam bolt on the top is a taugh 1 thats why i had mine done cause i watch the mechanic and it took him almost an hour to do so if u can afford it let them do it

Feb 03, 2009 | 1996 Lincoln Town Car

1 Answer

Starter or solenoid only


if you here click when trying to start a somewhat strong click then the solenoid is good check cable on side going to starter if tight starter would be the problem.

Jan 29, 2009 | 1991 Lincoln Mark VII

1 Answer

1991 Lincoln Mark VII LSC spark plugs and wires


you don't have to worry about a special tool if you are replacing the wires but you will need a 5/8 socket with a rubber boot and an extension and maybe a swival to remove the plugs if there is an auto zone near by they will print you out a diagram for free

Jan 07, 2009 | 1991 Lincoln Town Car

2 Answers

Starter


hi,

take off the passenger side front tire and youll have to use a couple of socket extensions to get it, make sure to jack and block car correctly. when you remove the tire you should be able to see the top bolt with a droplight through the wheelwell
access is through the wheelwell I believe.

J

Sep 07, 2008 | 1991 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...