Question about 2002 Mitsubishi Lancer

1 Answer

Do you tork rotors - 2002 Mitsubishi Lancer

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Yes, it is very important that you torque the wheels on your car. The correct torque for your model is 80 ft-pds. After driving 50 miles you need to re- torque to 80 ft-pds . That is because the lugs can loosen . This is especially true with aluminum rims. The reason you carefully torque the wheels is so your brake discs/rotors do not warp when they get hot and of course so the wheels do not fall off. Do not over tighten your wheels, this will warp the discs/rotors. Torque your wheels and then after fifty moles re-torque the wheels.

Posted on Sep 16, 2010

  • David Belcher
    David Belcher Sep 16, 2010

    Your very welcome.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW DO YOU INSTALL A CRANK POSITION SENSOR 1999 CHEVY ASTRO VAN 4.3 LTR MOTOR


The crank sensor is inside the distributor and may also be called an HEI pickup.
Disconnect wiring harness and remove the two tork head screws and lift out. Now would be a good time to replace the rotor & distributor cap if you haven't done so lately.
I hope this helps.

Jul 07, 2011 | 1999 Chevrolet Astro

1 Answer

Half Shaft


pull off hub cap remove circlip in the nut if there is one, then loosen axle nut. Need a breaker bar and wheel on the ground. once nut is off loosen lug nuts, jack up car on side . bolts #10 Tork on some models then remove. Remove lower tie rod end remove bolt and nut. remove rotor and 2 Caliper pull out on the bolt. push lower control arm down with a bar and pull strut Assembly out away from car. next pull axle out using a flat bar to shove the axle out of transmission. install is in reverse.

Mar 23, 2010 | 1996 Plymouth Voyager

2 Answers

Cant remove front rotor


If the brake caliper bracket is out of the way, use wd40 around the center of the hub, then tap the rotor all around with a hammer. Most likely a little rust is holding it on.

Jan 10, 2010 | 2002 GMC Sierra

2 Answers

Need torque settings for honda ballade cylinder head bolts


dear friend-your torque setting is cold 66 nm

Jul 23, 2009 | 1998 Honda Civic

1 Answer

Did I replace my rotor correctly


You completed the job correctly, what holds on the rotor in place is when you install the tire and tighten the lug nuts.

Apr 22, 2009 | 2003 Jeep Liberty

1 Answer

2003 V6 Jeep Liberty Limited how do I remove front brake rotor


Hole with notches is likely a torks screw Looks like an allan key hole with extra splines? they make a bit that fits in there. It's on the flat surface where the wheel mounts right?

Apr 22, 2009 | 2003 Jeep Liberty

2 Answers

How do I change the rotors on a 2003 buick rendezvous?


You will find two bolts on the back side of the caliper that go into two small rubber boots. Likely the bolt heads on yours are torks head and need appropriate socket to remove. You need to retract pads in order to easily remove caliper from rotor. Retract further with a large "c" clamp before re-installing pads. Lube slides that attachment bolts go through (I use white grease for this) before re-installing them. Be careful to not cross thread bolts when putting them back in.
Good luck, and don't forget to rate this answer!!!

Mar 25, 2009 | 2003 Buick Rendezvous

1 Answer

Need to know the tork on rocker arm and intake for 2000 sonoma 4.


rockers get 22 ft. lbs.
lower intake gets 27, then 106, then 134 inch lbs
upper intake gets 44, then 80 inch pounds

Jan 10, 2009 | 2000 GMC Sonoma Extended Cab

1 Answer

2003 Hyundai Tiburon Gt rear brakes


hi not conversant with the tiberon in uk but will try to help ? if you remove the rear wheel then look at the brake disc (rotor) most hyundai rear discs on uk models are secured to the rear hub by 2x screws posidrive or tork heads ? if this is so on yours then no problem you will have to remove the caliper first from the carrier 2xbolts h/brake off then undo 2xbolts securing caliper carrier tosuspension stub assy your disc /s are most probably vented discs? or may be standard discs? remove the screws then you may have to hit disc from behind with hammer to jolt free as they are sometimes rusted on due to high temps and rain ideal conditions to create rust as you prob know? re assemble is reverse hope this helps ?

Oct 20, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...