Question about 2001 Pontiac Montana

1 Answer

What size is the nut holding on the front rotor on the pontiac montana 2001

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Measure it flat side to flat side ....inches can be converted to metrics....

Posted on Sep 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wheel came off


check lower control arm/ ball joint. install new studs and lug nuts

Aug 11, 2012 | 2002 Pontiac Montana

2 Answers

How do i remove the drive axle on a 2001 gran prix


*1. Remove Wheel, *2. Remove CENTER OUTER AXEL NUT Size is " 36 or 34 mm #3 Tie Rod End Remove #4 LOWER BALL JOINT Nut and Seperate it, Using a BENT TIPED PRY BAR Pop Axel < This Step Sometimes Requires Some Finess and Manipulation but It WILL COME OUT, SOME Have A Carrier type Bearing with them if so Remove it also.

May 12, 2010 | 2001 Pontiac Grand Prix

1 Answer

2000 pontiac montana. I want to replace the driving ligh bulbs. the under the headlights what size is it?


Fog/Driving Light Bulb Size: 880
Here is the rest of the bulb size used in your Montana.
2000 Pontiac Montana Auto Light Bulb Diagram
Low Beam Headlight Bulb Size: 9004
High Beam Headlamp Light Bulb Size: 9004
Parking Light Bulb Size: 4157NALL
Front Turn Signal Light Bulb Size: 4157NALL
Rear Turn Signal Light Bulb Size: 3156
Tail Light Bulb Size: 3057
Stop Light Bulb Size: 3057
High Mount Stop Light Bulb Size: Assembly
Fog/Driving Light Bulb Size: 880
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3156
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 558
Glove Box Light Bulb Size: 194
Map Light Bulb Size: 168
Dome Light Bulb Size: 562
Step/Courtesy Light Bulb Size: 168
Trunk/Cargo Area Light Bulb Size: 212-2
Daytime Running Light Bulb Size: 3157NALL
Thank you for using fixya.


Apr 30, 2010 | 2000 Pontiac Montana

1 Answer

How do you install a front wheel bearing on a 2001 Pont Montana


jack the vehicle up remove the wheel
remove the brake caliper bottom bolt 15mm. lift the caliper up and slide the caliper pin out
remove the caliper housing bracket 2 - 15mm. bolts
remove the brake rotor
remove the drive axle nut 1 5/16
the remove the hub bearing bolts 3- 13mm. they are in behind (best to use a 13mm flex socket)
disconnect the ABS harness
use a hammer and hit the hub bearing flage (it maybe corroded )
now the hub bearing is out clean the steering knuckle with sandpaper to remove corrosion
install the hub bearing (make sure the ABS harness is in the right position)
and reassemble
hope this helps

Apr 29, 2010 | 2001 Pontiac Montana

1 Answer

How to change thermostat on a 2002 Pontiac Montana


I believe the Montana has a 3.4 Liter V6 Engine.
This thermostat is located under the exhaust "crossover" pipe that runs between both the front and rear cylinder heads. Divers side.
Remove the heat shields (10mm bolts) and then the nuts on the exhaust studs. (6 total)
Two bolts hold the T stat housing to the intake.

Feb 23, 2010 | 2002 Pontiac Montana

1 Answer

2004 Pontiac Grand Prix Tyring to change rotor. What size nut holds the rotor on?


THe rotor is not held on by nut. If you are talking about taking the axle off and axle nut is abut 1 3/4 - 1 7/8

Sep 26, 2009 | 2004 Pontiac Grand Prix

2 Answers

2003 Pontiac Montana Front Wheel Bearings


Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Apr 08, 2009 | 2003 Pontiac Montana

1 Answer

Rotor


You do not need to pull the axle nut loose the rotor will slide off wheel hub assembly.you might need to tap it off if been on a long time.all that has to come off is the caliper

Aug 20, 2008 | 1998 Pontiac Grand Prix

Not finding what you are looking for?
2001 Pontiac Montana Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...