Question about 1985 Ford Bronco II

1 Answer

Unable to bleed hydraulic clutch system - 1985 Ford Bronco II

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,340 Answers

Bench bleed the master cylinder FIRST, or you may never be successful. Parts houses sell a bleeding kit that screws into the output line of the M/C and allows the other end of the hose to go into the reservoir, allowing for bleeding.
After bleeding the M/C, do not let fluid run low, or start over again.

Posted on Sep 16, 2010

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
fastboyz
  • 674 Answers

SOURCE: bleeding hydraulic clutch

well you will need some help
make sure the resivor is full and have someone hold the clutch pedal to the floor and crack the bleeder on the slave cyl. and close after the spert of fluid comes out. when the screw is closed have the person in the drivers seat slowly let up and push down 3 times and hold down and bleed one more time. refill your resivor and repete if you dont think the peddal is quite right. just dont run it out of fluid
good luck it realy isnt that hard.
later paul

Posted on Sep 16, 2008

  • 1201 Answers

SOURCE: bleeding the hydraulic clutch

Have somebody pump the pedal fast about 3 or 4 times, on the last pump hold pedal down and close bleeder. Make sure fluid stays full in master cylinder, try it again, if it still doesn't work, then you might have a bad slave valve, if you haven't already replaced it.

Posted on Jan 30, 2009

cat_daddy887
  • 2 Answers

SOURCE: how do I bleed hydraulic clutch in 1991 jeep

There is a bleeder on the drivers side of the transmission follow the tube from the clutch master cylinder if you cannot find it. Pump the clutch up and hold it down then open the bleeder repeat till air is gone. May have to bleed again after driving a bit. If you want to bleed the clutch master cylinder run a tube from where the line goes into the cylinder and take the cap off and run the tube into the fluid (make sure its in the fluid) then pump the clutch slowly until no air bubbles. I just replaced my clutch master cylinder this is where the information comes from hope it helps you out!

Posted on Apr 05, 2009

emissionwiz
  • 76164 Answers

SOURCE: how to bleed a hydraulic clutch on a peugeot 406

you need to buy a vacuum clutch bleeding tool make by a company called MITYVAC

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 s 10 clutch wont catch after bleeding it replaced masre and slave clutch


Are you sure all the air is out of the system and you have a firm pedal feel. If not have a shop pressure bleed the clutch hydraulic system.

Apr 21, 2016 | Cars & Trucks

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

I have an 84 Honda shadow vt700. The clutch was working but would slip when hot it would get to where I could release clutch with bike in 1st gear and nothing would happen! It would just continue to idle!...


Bleeding the hydraulics will not improve the friction drive of the clutch in any way,your clutch drive plate is worn out and needs replacing. To bleed the hydraulic line ,make sure that the master cylinder is fully topped up,pump clutch lever several times then tie ,using a zip tie the clutch lever all the way to the handle bar,gently open the bleed screw and await fluid to start dripping from the bleed screw, this may take an hour or two but it will eventually bleed itself,once 25% of the fluid has discharged from the the master cylinder tighten up the bleed screw and this is the easiest DIY way of bleeding a hydraulic system, without a pressure bleeder.

May 04, 2017 | Cars & Trucks

3 Answers

How do you bleed the clutch hydraulic system on a 2008 Mustang?


you bleed a hydraulic clutch the same way you bleed a brake system and it uses brake fluid as well.you keep bleeding until there is no more air in the clutch system.there should be a bleeder screw on the clutch slave cylinder that is were you bleed the clutch from.

Mar 18, 2011 | 2008 Ford Mustang

1 Answer

Clutch slave cylinder how to bleed


HYDRAULIC SYSTEM BLEEDING Do not use fluid which has been bled from a system to fill the reservoir as it may be aerated, have too much moisture content or possibly be contaminated. Clean the dirt and grease from the cap to ensure that no foreign substances enter the system. It is also important to maintain the fluid level in the clutch reservoir to the top step with hydraulic clutch fluid Hydraulic Clutch Fluid GM P/N 12345347 or equivalent.
  1. Attach a hose to the bleeder screw on the clutch actuator assembly and submerge the other end of the hose in a container of hydraulic clutch fluid.
  2. Depress the clutch pedal slowly and hold.
  3. Loosen the bleeder screw to purge air.
  4. Tighten the bleeder screw to 18 inch lbs. (2 Nm).
  5. Let up on the clutch pedal.
  6. Repeat Steps 2 through 5 until all air is purged from the system.
  7. Fill the reservoir to the top step with hydraulic clutch fluid.
  8. Repeat this bleeding procedure if there is a grinding noise during the clutch spin down procedure.
prev.gif next.gif

Oct 13, 2010 | 1998 Chevrolet Cavalier

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

Clutch pedal went too floor pulled back up now solid and not lettin engage gears


It is probably a hydraulic clutch. Check the fluid. From your description, I am understanding that the pedal feels normal but you are unable to put the car in gear when you push the pedal down. You probably have a leaky slave cylinder on the transmission, but it is possible to have a leaky master cylinder (on the firewall, aligned with the clutch pedal). Check your fluid, if it's empty fill it and bleed the system. You probably have a really big air bubble in your clutches hydraulic system. Usually you can get away with not replacing the leaking part for a bit, just keep an eye on your fluid, and save your pennies! Good luck!!!

Mar 05, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Audi a3 1996 1.6 5 speeds model. 1st flexi clutch pipe split..no clutch replaced pipe now no gear change..could it be worn clutch? car is in garage! help tp


First you must air bleeding out from inside hydraulic clutch acting system ! On the slave cylinder you will find an aeration screwed ventil provided for air bleeding. See picture below:

ee99bec.png Two person are necessary for this operation. One person for acting the clutch pedal and another person for air bleeding out from inside hydraulic clutch acting system by unscrewing the aeration ventil from slave cylinder. This operation is difficult, and must spend some time for successful result!

Jan 28, 2010 | 2005 Audi A3

Not finding what you are looking for?
Cars & Trucks Logo

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...