Question about Chrysler Sebring

1 Answer

I changed the battery in the remote. The starter will start the car but when I try to put car in gear and press the brake the car shuts off. Normally that would not happen.

Posted by on

  • lthomas_11 Sep 16, 2010

    How would I do that? 2003 Sebring

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,297 Answers

I am assuming, since you did not indicate year, make and model of your Chrysler that you have an aftermarket remote starter?

problem is now you need to reprogram your anti-theft computer/models

Posted on Sep 16, 2010

  • Sean Reisdorf
    Sean Reisdorf Sep 16, 2010

    you need a Chrysler scan tool or the $8000 snap-on version

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2001 Nissan xterra turned on all by its self. When I got to it i unlocked my running car put the key in the ignition and nothing happened I tried turning it off with the key but didn't work. The car...


The car apparently has a remote starter installed. This allows for starting the engine without a key. Most aftermarket starters will run for 15 minutes, then if you haven't entered the car and inserted the key to the on position, it will shut off automatically. The only way to shut the car off while the remote is in control is to press the brake pedal. The key won't work to turn it off UNLESS you get in the car, turn the key to the ON position, press the brake, THEN turn the key off.

Dec 22, 2014 | Cars & Trucks

2 Answers

Starter wiill not even engage turned the key on and nothing ran fine when I parked it and got up in the morning and wont even tur n over. Brand new battery


Hmm, possible problems:
- starter or starter solenoid defective.
- neutral switch or wiring thereto defective. Shift selector has to be in Park or Neutral to start. Sometimes brake pedal has to be pressed also for starter to turn.
- remote starter system defective (if you have this) This would be hard to diagnose.
I would first confirm if the starter works by putting 12V directly from positive pole on battery to positive connector on starter solenoid (use jumper cable, and wear goggles in case of massive sparking when you accidentally touch ground.)

Sep 10, 2014 | 2002 Chrysler Sebring

2 Answers

Why wont my car start


Possibly a battery cable terminal or the connection at the starter.
Sometimes a loose or faulty wire can barely work until a load is put on it then it just shuts down. Test power flow at starter before and after turning the key. Replace battery cable ends and if the problem persists, replace entire cable.

Aug 01, 2014 | 2003 Ford Taurus

2 Answers

When I put the key in the ignition it doesn't try to start everything else comes on then shuts off. I drove it yesterday but now it won't work


The remote starter module is not getting an electrical signal when you turn the key to the on position after remote stating the vehicle. When you depress the brake without turning the key on the vehicle shuts down. The remote module thinks the key is off even when you turn it on. There is a loose connection or the remote start device is defective.

Jun 04, 2014 | 2005 Chrysler 300

1 Answer

Hi -\r\n2007 Grand Marque Auto trans stuck in Park. Wont move to gear. Case study: Just have remoate start put in, Steering wheel is easy to turn, car starts, Back lights operate (Except 1 bulb in third...


Check brake light switch behind brake pedal remote start has to be wired into switch so vehicle will shut down when brake is depressed when put into gear without ignition switch turned on. possible bad connection on switch or wires are not attached.

Nov 27, 2010 | 2007 Mercury Grand Marquis GS Sedan

1 Answer

Battery has full charge. connections are good, but every 10th time or so I try to start it, battery will not turn starter. If I pull positive cable and put it back on, car will start normally until the...


THE NEXT TIME IT FAILS MAKE CERTAIN THE CAR IS IN " PARK " OR OUT OF GEAR SET THE EMERGENCY BRAKE,WHILE SOMEONE IS HOLDING THE IGNITION SWITCH IN THE START POSITION & MEASURE THE VOLTAGE AT THE BATTERY & AT THE STARTER SOLENOID OR RELAY, IT SHOULD READ 12 VOLTS AT THE BATTERY , IF THE VOLTAGE IS THERE, YOU MIGHT TAP ON THE STARTER { IGNITION SWITCH STILL IN THE START POSITION. IF TAPPING THE STARTER MAKES THE STARTER WORK THE STARTER NEEDS TO BE REMOVED & CHECKED & OR REPLACED

Nov 19, 2010 | 2003 Mitsubishi Galant

1 Answer

Well first thing to start is it is a 1990 stanza xe with 160000 original milage and it started fine on sunday then went to go to work on monday went to start it and it tried to start bogged down and the...


Your car probably has an aftermarker remote car starter module installed that you reset, by changing the battery. It has nothing to do with your actual car starter. You will need to shut down(valet) or uninstall that aftermarket remote car starter module to get it to stop trying to start your car with no keys in the ignition.

May 21, 2010 | 1990 Nissan Stanza

1 Answer

Cant push the button to put in gear


CHECK MAKE SURE BATTERY FULLY CHARGED IT HAS TO BE 12.5 VOLTS BEFORE THE BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID WORKS.IF BATTERY POWER GOOD CHECK BRAKE LIGHTS TO SEE IF BRAKE LIGHTS SWITCH IS WORKING.IF NO CHECK FUSE.IF FUSE GOOD BRAKE LIGHT SWITCH IS FAULTY. IT CONTROL THE BRAKE TRANSMISSION SHIFT SOLENOID ALSO THE NEUTRAL SAFETY SWITCH.IF FUSE AND BRAKE LIGHT SWITCH IS GOOD.YOUR PROBLEM COULD BE A FAULTY NEUTRAL SAFETY SWITCH OR BRAKE TRANSMISSION SHIFT SOLENOID FAULTY.

May 05, 2010 | 2001 Chevrolet Cavalier

1 Answer

I own a 2002 Toyota Rav 4 - 5 speed, when I purchased it I had a remote car starter installed and it worked great until now. If I use my car starter and I stall my car out it will not start again for about...


You either have a bad remote starter, or the remote starter has caused the body computer to fail. Remove the remote starter completely from the car. See if the car starts normally. If not, the body computer has failed. This is a very expensive item, and have been found to malfunction due to remote starter electrical failures.

Nov 10, 2009 | 2002 Toyota RAV4

1 Answer

I cant start my car with the remote starter


You normally have to while the car is running transmition in neutral push the brake pedal, put the emergancy brake on, release the foot brake, press the remote start button on the remote, take keys out of ignition switch, car should stay running, get out, press the lock button on remote starter remote, car should shut off, and now is set

Feb 05, 2009 | 2002 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...