Question about 2004 GMC Sierra

1 Answer

Transmission issues revving up and not going in gear smoothly

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 193 Answers

I sounds like you may be low on transmission fluid. Its hard to say with the limited information yuo have given. If you put it into drive and the vehicle sits there and you give it gas and the engine revs up and then slowly starts moving, it is a transmission problem. If it is low you may have already done irreversible damage. The problem will get worse very quickly. Check your trans fluid immediately.

Posted on Sep 16, 2010

  • krisbruner Sep 16, 2010

    plenty of tranny fluid

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Transmission wont change gear


Assuming auto transmission? check fluid level and linkages...

does it drive but won't change gear, or not select gear?

Feb 03, 2016 | 1995 Mercedes-Benz E 280

1 Answer

What are the problems of a faulty transmission speed sensor in a 2002 land rover discovery 2 v gas?


run the fault codes and look for a faulty torque converter clutch solenoid /servo and a problem TCM unit. A service if not done in the last 60.000 miles would also help.

Dec 16, 2014 | 2002 Land Rover Discovery Series II

1 Answer

Hello, So I've been having a few issues with my 2012 Suzuki swift revving to high & having issues changing gears. I've been told to factory reset the chip. But I'm not sure how to? Help :) Thanks in...


probly need a transmission update--go to a independent mechanic who does a data stream using factory gear--its a scan displaying values and can download the lastest info--makesure they hav xperienc in this area and the equipment--a little code reader wont cut it---

Dec 02, 2014 | Cars & Trucks

1 Answer

Transmission snapping when shifting gears( when changes gears)


Could be a problem with the throttle position sensor. It's clearly an electrical issue. Besides the noise, how does the transmission shift? Is it smooth, or does it slam into each gear, or does it seem unusually soft. Shifts should be firm but smooth.

Mar 06, 2014 | 2005 Chevrolet Uplander

2 Answers

Buick rendezvous gear shifts just fine but car won't move. No grinding shifting is smooth and flawless vehicle just will not move forward whether it is in drive, 1st, 2nd, or third gear. Reverses and


Sounds as if forward driving gears are shot. Different gears make vehicle move in reverse. I would ask if transmission fluid level when checked is in the operation range or full.

Nov 07, 2013 | Cars & Trucks

1 Answer

Transmission Fluid Pressure Sensor/Switch


Not so baffling given that Chrysler has major issues with TCM units. Reset the whole thing with a power disconnect and see what it does.

Jul 08, 2017 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Very slow to kick in to reverse, first and second gears accompanied by high revving sound. Not a smooth transition to other gears as well. High revving until going. Very high fuel consumption as well. Once...


it sounds like your transmission is slipping. they make this chemical you can get at a part store, its a transmission stabalizer. it should help with the grinding noise and transitions to the other gears. also give your truck a complete tune up (oil change, fuel and air filters, spark plugs etc.) it should help with the fuel consumptions.

Aug 13, 2010 | 1997 Chevrolet S-10 Pickup

2 Answers

Transmission issues with 3rd and 5th gear


It's weird but it's the problem!!! There is a switch on the transmission near the selector, usually only affects 3rd gear!!! The switch is being distorted after repetitive battering with gear selection!!! I have experienced it and also read about it in australia on a Navara!!!

Nov 17, 2009 | 2002 Nissan Frontier Crew Cab

1 Answer

92 Taurus-Not shifting into 1st, but once engaged, shifts smooth


Had that problem on a 93. There is a plastic piece inside the trans that cracked and needs to be replaced...=...Trans rebuild.

Mar 25, 2009 | 1992 Ford Taurus

1 Answer

Hyundai accent high revving during gear change


you may have a problem with the idle sensor located near the fuel injection system.

Oct 29, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
2004 GMC Sierra Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...