Question about Hyundai Elantra

1 Answer

MY ELANTRA HAS A CLUTCH RATTLE WHEN IT IS ABOUT TO MOVE.REPLACED NEW CLUTCH ,PRESSURE PLATE AND REL. BEARING.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,095 Answers

If it works leave well alone as its most likely the lay shaft bearings worn ,which is a big expensive job

Posted on Sep 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Hyundai elantra clutch problem. Replaced master and slave cylinders bled system. Now I have a stiff clutch pedal. Doesn't move at all. Bled out ok , just not sure now. Clutch out???


What was wrong to start with that made you replace the cylinders? There is a back story that will probably tell the tale. It could possibly be a locked slave cylinder - did it work in-out before installing? If not, its a pressure plate and/or throwout bearing bound up.

Hope this helps,

Scott
Europartsplus.com

Aug 23, 2015 | Hyundai Cars & Trucks

1 Answer

Car won t move in any gear


Did you also replace the pressure plate? Pilot bearing? If you replaced the clutch...and the car moved, and then stopped moving again...your issue is likely right there, bad pressure plate, flywheel may need resurfaced or replaced ETC. I am curious to know what the old clutch disc looked like when you took it out. Was it glazed or worn? I would pull the tranny again, and look at the new disc to see if it is glazed looking from slipping...and note if it is both sides, or one side, and which side...plate side or flywheel side. If you didn't replace the pressure plate/pilot bearing with the clutch disc...I would do that.

Mar 21, 2014 | Honda Cars & Trucks

1 Answer

Stiff clutch on 2002 elantra , clutch and transmission new , slave clinder pushes wrong way ,whats wrong ?


FYI, the slave cylinder is pushing correctly, the clutch is the 'PULL TYPE', not the 'PUSH' type.
Go to www.hmaservice.com and register the vehicle by VIN #. You'll then have access to Shop Manuals, Wiring Diagrams, Illustrations, Service Bulletins, etc.

The clutch on the 2002 Elantra, as I mentioned, is the "Pull Type". Instead of 'Pushing' on the throw-out bearing, it "Pulls" on it. The pressure plate engages when the bearing is released (when it is 'pulled' back into the pressure plate 'fingers'

Was the new trans & clutch installed at an authorized Hyundai Service Department? If not, you might want to have them inspect the installation to determine what's wrong. If it WAS installed by a Hyundai Service Dept, take it back to them & tell them to FIX IT!

Jun 30, 2011 | Hyundai Motor 2002 Elantra

3 Answers

I have a 2004 elantra. i had the clutch replaced at just under 100,000 miles. it has been replaced twice since. i am now close to 118,000 miles and am having trouble again. what is the problem? my mechanic...


Go to another mechanic! The mechanic you are using now isnt doing something right. The only way you should lose two clutch packs in 18,000 miles is if you are driving like on a nascar circuit! If you are driving normally, only something mechanically wrong can cause this.

Feb 13, 2011 | 2004 Hyundai Elantra

2 Answers

Just bought a 2004 Elantra (93000 miles) with 5 speed tranny. With the hood up and my daughter behind the wheel I noticed a rattling sound (in neutral) coming from the clutch/transmission area when the...


I would be checking the throwout bearing. But, if the clutch isn't slipping, maybe leave it for now?

If you put it in 5th gear, let out the clutch with handbrake applied and it stalls--the clutch isn't slipping for sure.

Jan 31, 2011 | 2004 Hyundai Elantra

1 Answer

Rattle sound when I hold in my clutch pedal


Hi:
A possible cause of this rattle is the clutch throw out bearing. It is wjhat pushes against the pressure plate to release the clutch. It does require the transmission to be removed to replace it, and while you have the transmission out, it would be a good idea to replace the clutch, pressure plate and pilot bearing too.

Oct 21, 2010 | 2001 Ford Escort ZX2

1 Answer

5 speed hard time shifting and it has a new clutch.


Replacing the clutch plate only sometimes doesn't help you should have replaced the clutch pressure plate too, best is to fit the clutch pro-kit (clutch plate, clutch pressure plate and release bearing).
I guess now you will have to just replace the clutch pressure plate and the release bearing.

Nov 23, 2009 | 2000 Kia Sportage

3 Answers

Clutch is noisy,when i depress the clutch the noise goes away


this noise is caused by a noisy clutch throw-out/release bearing, that is the part that presses against the pressure plate and disengages the clutch disk, the transmission must be removed to replace this part, so it is best to replace the clutch assembly at the same time, the labor for both is the same, about 5 hours

Oct 23, 2009 | 2003 Toyota MR2 Spyder

1 Answer

How do you remove the throwout bearing from the pressure plate?


YOU DONT
If your clutch pressure plate has a stuffed thrust bearing then you are riding the clutch pedal and the clutch is running all the time to burn out the bearing so the centre plate is 1/2 worn and pressure plate springs or toggles are getting week so the answer
is to replace both it will save doing the job in 2 months time (belive me)

Sep 24, 2009 | 2000 Hyundai Elantra

2 Answers

2005 rodeo 4wd turbo diesel


possibly the throw out bearing....which is part of the clutch assembly

Oct 09, 2008 | 2004 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...