Question about 1991 Ford F350

1 Answer

Motor What do i need to changeon a automatic 7.3 diesel motor to use it in a standered truck?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Nothing just the flywheel

Posted on May 30, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I locate the number one piston and the firing order on the 1999 New Volkswagon Beetle ? I need to take off the timingbelt to get to the water pump. I need to put the number one piston on the TDC.


To put at TDC, on the transmission housing, where it bolts to engine block, will have a rubber plug, remove and align pre diagram, there are for stander or automatic transmission, the one where you can see the flywheel is stander, or you could align the crankshaft pulley, hope this was very helpful.

b241739.pngccd9b89.pngcc7d882.png

Sep 15, 2010 | 1999 Volkswagen Beetle

1 Answer

Looking for the flow on fuel pump for 1984 lincoln mark 7 diesel


i just replaced mine with oem pump from rock auto

Jul 17, 2010 | 1984 Lincoln Mark VII

2 Answers

What type tramission fluid to use for 5speed manual-4cyle?


1992 Ford Ranger came with two different type of 5 speed stander transmission's that year.

For a Mazda stander trans it take's Automatic transmission fluid Mercon.

for a Mitsubishi stander transmission it take's Ford manual transmission fluid.

Hope this help's.

Jun 28, 2010 | 1992 Ford Ranger

3 Answers

Can i jump start my 1985 nissan truck if starter is shot, I tried to jump start my truck but it wouldn't start


If the starter is shot no jump start should not work. The starter is what spins the motor.

Jun 12, 2010 | 1985 Nissan Pickup

1 Answer

How much coolant in radiator of 1998 Ford Contour 4 cylinder


2.0L engine

stander transmission 7 qts.

automatic transmission 7.5 qts.

50/50 mixture.

Jun 08, 2010 | 1998 Ford Contour

2 Answers

Will a 87 ford ranger v6 4 wheel drive trans. fit in a 86 ford ranger 4 cyl 4 wheel drive


If automatic transmission wont work engine block's are not the same, if stander transmission you could swap out bell housing held on with four bolt's from one to the other. Good luck and hope this was very helpful.

May 19, 2010 | 1986 Ford Ranger 2WD

1 Answer

Battery changeon 2002 sonata,now no heat


on this car, there is a sensor that has caused this problem. auto stores can't fix it. it's a dealer only repair. sorry.

Nov 14, 2008 | Hyundai Motor 2002 Sonata

1 Answer

Serpentine belt diagram for a 5.9 diesel with air and 9 pulleys


5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Sep 13, 2008 | 2008 Dodge Ram 3500

1 Answer

I have a landcruiser 1994 gas. i one too change it for diesel


to change a gas to a diesel is a very big project. you will need all new feul system, lines, filters, pumps, etc. then the motor has to fit the trani. which is hard to find, so you might need a new trani. then braking, cooling, heating, and so much more. but if you still want to the best thing to do is get a convertion step- by- step book. if you found someone that could tell you. they would need to know what car exsactly and what motor you would be putting in to it.

Jun 13, 2008 | 1994 Toyota Land Cruiser

Not finding what you are looking for?
1991 Ford F350 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...