Question about 1999 Ford Explorer

1 Answer

Over drive light on - 1999 Ford Explorer

Posted by on

  • johnny mcneely Sep 16, 2010

    most likely the switch to the overdrives bad,,push button on left side, where turnsignal is,right? if so, you'll have to replace the whole switch where the turn signals located. hope this helps!!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 107 Answers

Push the button at the end of the gear shift handle the light will go out. Just means that your not in over drive when crusing. Some cars have a 5th or 6th gear to save on gas while crusing. The light should be in the off position 99% of the time

Posted on Sep 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It goes in all the 4 wheel drive but want go in 2 wheel drive and a navigator have light inside that show that its in two wheel drive 1998


The vast majority of vehicles that have 2 wheel and 4 wheel drive will only light up something on the dash when in 4 wheel drive.(They also light up 4 wheel drive low if you have it) I've been driving 4 wheel drives for 25 years and have yet to see one that lights up something for 2 wheel drive.

Sep 06, 2016 | 1998 Lincoln Navigator

1 Answer

Can I legaly drive without the brake lights and what is the penalty for driving without the brake lights


NO--- you cannot drive with out brake lights
The penalty will be the local or state fine
The real penalty will be a rear ender that occurs because of no brake lights where you loose insurance because you have been driving an un-road worthy vehicle

Mar 13, 2015 | Cars & Trucks

1 Answer

I have a 2500hd silverado 02 6.0L light above bumper I think its a driving light but my driving lights are my low beam head lights how do I get them to come on?


Okay those lights are called your driving lights. they only come on during the day, when headlights are off, they are for safety. i know this would drive me crazy, a customer would come in and say i have a light out and i would check and all was fine. the way it works is during the day, headlights off and truck must be in drive,

you will need some one inside holding the brake and put in drive with headlights off for you to see them and see if they need bulbs. let me know the outcome .good day

Dec 25, 2012 | Cars & Trucks

2 Answers

Engine warning icon on my dashboard indicates emission problem can I still drive my car until repaired


As long as the light is yellow and not red you are fine to drive . The yellow is just a caution light . If any red lights come on thats when you need to stop or not drive it

Aug 05, 2012 | Saturn Cars & Trucks

1 Answer

Engine flutters loudly at stop lights. Sounds normal when driving.


You should not drive a car if the check engine light comes on and you do not know what the problem is. In some cases the check engine light means a serious problem and I know could cost a lot of money to repair. Mine came on and cost $800 dollars to repair as I tried to drive it.

Dec 29, 2017 | 1991 Ford Explorer

1 Answer

Where to hook up power wire for aftermarket driving lights in 93 Nissan Maxima


if you hook the driving lights to the low beam circuit you will be in breach of traffic regulations the regulation reads that driving lights can only be operated with high beams and on selection of low beam , the lights have to go out
added to that is the clause --the driving lights most be extinguishable when on high beam by the use of a separate isolation switch
now the circuit is really simple
you place a relay for each driving light in a suitable place
you run a fused wire from the battery to the relay and then to each light
to make those relays work you connect a wire from the existing high beam relays connections(m piggy back or like connection) so that when on high beam the trigger power that puts the headlights on also triggers the driving light relays
Now to meet regulations you run ground wires for the driving lights back to a switch in the cabin then to ground

Oct 31, 2017 | Nissan Cars & Trucks

1 Answer

One of my driving lights went out after hitting a bump on a dirt road, how do I replace the bulb? It's not the headlight, it's the driving light or fog light.


One of my driving lights went out after hitting a bump on a dirt road, how do I replace the bulb? It's not the headlight, it's the driving light or fog light.

Jul 11, 2009 | 2005 Volkswagen Touareg

1 Answer

Left drive lights not working


It sounds like a couple of blown bulbs. Open up the light fixture where the drive lights are found and replace the bulbs.

Nov 27, 2008 | 2005 Dodge Durango

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5685 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...