Question about 1996 Pontiac Grand Am

1 Answer

Clutch went out..what do i need to buy? - 1996 Pontiac Grand Am

Posted by on

  • Jeff Turcotte
    Jeff Turcotte Sep 16, 2010

    what is the symptom--what do you mean by "went out"


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 118 Answers

I would go to your local parts house and ask for a New Clutch Pak
which should have a new clutch disc,pressure plate,throw out bearing and a pilot bearing and a alinement tool. Than I would see if they have a replacement flywheel. The reason for the fly wheel is due to hot spots and uneven wear on the fly wheel.If you do not replace your flywheel or have it machined you will get chattering everytime you step on clutch

Posted on Sep 16, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My clutch went out on my 2002 pt cruiser and it is a Manuel. Transmission 4 cylinder.. is replacing a clutch a very difficult job and how many hours

Yes, but mainly for the equipment required. A tip would be to buy the part yourself first. It's an all-in-one part and costs in England they are £330 (just the part) and the job is easily done in under a day. Again....up a ramp with good knowledge of clutches.

Dec 16, 2014 | Cars & Trucks

1 Answer

I was driving my manual 91 dodge stealth home when i went to shift into 4th gear the clutch pedal went all the way to the floor and stuck and now it doesnt like to go into gear with the clutch in but it...

Clutch disk or pressure plate or both are worn out, and I would replace the throw out bearing. You can buy a kit at autozone or kragen that has everything all together 100-200 dollars.

Aug 10, 2013 | 1991 Dodge Stealth

1 Answer

Which fuse can cause it not to crank?

there is a neutral saftey switch on the clutch pedal make sure it is pressing in enough to crank vehicle these sometimes get pushed outb and need readjusted

Sep 06, 2012 | 2007 Toyota Tacoma

1 Answer

My car sat for about 5 months in the yard. Clutch and transmission are new rebuilt. Went to move the car clutch went to the floor and stayed there. What can I do?

Sounds like you either need to bleed the clutch slave cylinder, or you need to rebuild or replace the clutch master cylinder and slave cylinder. You might want to check with the shop that replaced the clutch and rebuilt the transmission. It may be covered under their warrantee.

Dec 24, 2009 | 1987 Nissan 300ZX

2 Answers

Fan blade pretty much exploded while i was driving the other day. Do i need to replace the fan clutch as well? I don't want to buy a new blade and have the same thing happen because the clutch is bad as...

replace clutch as well-could have been damaged when fan let loose --rough idle -bad fan would give u a vibration that could feel like it was running rough

Nov 02, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

96 Saturn SC-1 clutch replacement problems

Sounds to me like there is an alignment issue witht he clutch disk. DId they buy a clutch kit with install tool? If not then good chance its not aligned and will need to come back out to align. you can also pick up a universal clutch alignment tool from autoparts store.

Jan 26, 2009 | 1996 Saturn SC

1 Answer

2004 Jeep G/C 4l V6

Unless you can find a way to route a different belt to go around all necessary pulleys without the a/c compressor, the only thing I can think of is to buy a junkyard unit and install it without freon, leaving the compressor clutch plug disconnected 'till you can get home to do the job right. Even if you need to buy the tools to do the job it's still cheaper than towing or a shop repair. Changing the compressor bearing requires special tools that you likely dont have in your back pocket!!

Dec 02, 2008 | 2004 Jeep Grand Cherokee

2 Answers

My transmition clutch went flat and can not put the car in any gear
sounds to me that you need to have your clutch changed above is a link I have found that tells how a clutch works

Nov 05, 2008 | Subaru Forester Cars & Trucks

2 Answers

Clutch problem

Likely need to buy a new clutch cable and install,and adjust for proper freeplay,and also possibly address the hole in the firewall .The hole needs to be looked at to make sure it is not oversized,cracked,bent,or otherwise unable to retain the cable.

Jul 11, 2008 | 1994 Mitsubishi Mighty Max

1 Answer

Instructions for replacing the clutch in my 1995 Honda Passport.`

Tony,its not worth it to mess with the clutch---goto a junkyard and buy an ac compressor.

May 24, 2008 | 1995 Honda Passport

Not finding what you are looking for?
1996 Pontiac Grand Am Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides