Question about 2007 Honda Accord Sedan

1 Answer

How do I program my garage door opener. i have no manual in my car

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 143 Answers

Press and hold the two outer buttons on the homelink system in the car until the led flashes rapidly or goes out. Then hold the programmed remote up to the homelink system and at the same time press the button on the remote and the button on the homelink until the led light blinks rapidly or goes out. It should take less than 30 seconds. ----- Then go to the motor head and press the colored learn button on the motor head and go back to the home link and press the homelink button 3 times to activate. If your opener has dip switches stop at -----. Thanks BB

Posted on Sep 17, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Doorguy27
  • 30 Answers

SOURCE: program my garage door opener

What the last guy post is correct, but you have to tel your car what kinda remote you have. Assuming you have homelink Which 95 percent of the cars do ill give you a very short version on how to do this. First thing you need to do is clear the code in your car from any other owners. Do do this turn your car's key to the on or acc non running position. Press and hold the first and last button. Untill the light reacts different ether starts flashing or flashes faster etc. Then you need to get one of your remotes. Press and hold the button you want to set in your car and press your remote button at the same time untill the light reacts diferent. Mind you hold your garage remote as close to your car remote as you can. Then finally Find your learn button on your garage door opener it's self it can be in the back or the front if its in the front you have to remove the cover press the button once DO NOT HOLD IT. then go to your car and press the button you set for about 2 seconds and repet 1-2 more times untill your garage door moves. Make sure nothing is in the way of the garage door. (I know that should go with out saying.)

Posted on Feb 10, 2009

  • 1348 Answers

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

Posted on May 14, 2009

picatudo
  • 239 Answers

SOURCE: Program car to garage opener

on the garage door opener there is a button, that is called the" learning button "you press that button until light blinks, then within 20 seconds press the open button inside car.

Posted on Feb 01, 2009

  • 9 Answers

SOURCE: program a garage door opener in 2004 buick rendezvous

I cannot find the 2004, but you can buy it from the dealer. You can download the 2003 and 2005 from this link. http://www.extendedgmwarranty.com/owners-manual/buick_owner_manuals.html

Posted on May 22, 2009

crapiemael
  • 241 Answers

SOURCE: need to program/link garage door opener with the one on the visor in the car

Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remote door opener


So, you get out your remote control to your garage door opener and, then get your owners manual to your new car. You need to follow the instructions from the manufacturer to be able to program the remote control to the car.

Ok, you have followed the instructions from the car manufacturer and you press the button for the garage door to go up.......and nothing happens. So, then you think you have missed a step on the programing. Well, what most instruction manuals leave out is the step from programing the car/truck/van to the garage door machine itself. On the back side of your garage door opener is a panel called the logic board. The logic board is the computer or brain of the machine. Most new garage door openers now are a mulit-code machine. By that, i mean it uses several signals each time you press the button on your remote control. This is for security, so your code can't be stolen by a code-grabber.

Now, comes the step of programing the vehicle to your garage door opener. Once you have followed the instructions of programing your vehicle, you now have to "teach" the car to the garage door opener. You will need some help doing this. You will have to get someone to press the button in your vehicle and hold it down, while someone else has to press the learn button on the back your your garage door opener mounted on the ceiling. The learn button on the back of your machine will be square if using a liftmaster machine. Craftsman, Liftmaster, Chamberlain are all the same. Their learn buttons are square, and usually are yellow, red/orange, or purple. If using a Genie, it has a button that says "learn button".

The person pushing the button on the machine will only have to push and release the learn button. DO NOT hold this button down. If you do, it erases all of the programing in the machine, and you have to re-program all the remote controls that you have. You will have to read my other hub to find out how to do that. You will probably say a few words you shouldn't either. :-) Programing the vehicle to the machine only takes a second, and when the machine accepts the code, the light bulb on the machine should flash for a brief moment, and you should hear audible click. Yep, it's that easy! I dont know why the auto makers leave that step out. Anyway, i hope this helps, and if you have any questions.. leave them in my comments and i will try to walk you through it. See the photo above and you will see the typical logic board...the square red/orange learn button is easy to see. Just remember to press and release

May 08, 2012 | 1995 Lincoln Town Car

1 Answer

Need to program/link garage door opener with the one on the visor in the car


Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

May 29, 2009 | 2006 Audi A4

3 Answers

How to program the volvo V 70 XC 2008 garage door opener


Simply hold down the button you want to use (there are 3 for up to 3 different garage doors) until the light flashes and keep holding it down. Now place the garage door opener up near the sun visor and hold it's button down until the light on the on button you are programming flashes. It is now programed. The other 2 are done the same way. Good luck. It took me a while to find the info, it's not in any Volvo manuals I could find.

Mike

Apr 26, 2009 | 2008 Volvo XC70

2 Answers

Program instruction garage door opener in 2005 chrysler pacifica


if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Apr 24, 2009 | 2005 Chrysler Pacifica

1 Answer

Program garage door opener in 2000 lincoln navigator


owner manual has instructions. Your garage door opener changes codes every time it is used so you need to push a button on your door motor and then run back to car to program while the door motor is willing to accept programming.

Apr 07, 2009 | 2000 Lincoln Navigator

1 Answer

Setting garage door opener


Most openers are programmed the same. You normally program the house garage opener to accept the new remote. Your garage opener will have a button to press to add in a new remote. Normally you press this and then press the remote in the car and hold until your lights on your opener flash or the garage door closes. (check your manual on your garage door opener)

Mar 27, 2009 | 2005 Chevrolet TrailBlazer

2 Answers

Universal garage opener


The solution is in the owners manual.If you want to program the "homelink transmitter" in your car,you will need a remote unit for your garage door opener to do this.It is fairly easy and straightforward.I programmed my 07 Pac and it works great.Good luck!

Mar 08, 2009 | 2005 Chrysler Pacifica

1 Answer

Program car to garage opener


on the garage door opener there is a button, that is called the" learning button "you press that button until light blinks, then within 20 seconds press the open button inside car.

Feb 01, 2009 | 2008 Hyundai Sonata

1 Answer

Garage door remote


First you have to clear any codes in there.
Hold down the outer 2 buttons until the red light blinks, could take a minute or less.
Then release the buttons, hold your garage door opener close to the button you want to program.
hold down the button on the garage door opener and the programing button until you get a blink from the little red light. That's it

Oct 10, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
2007 Honda Accord Sedan Logo

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...