Question about 2001 Chrysler Voyager

Open Question

How do you replace tail light bulb on 2001 chrysler voyager

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
eitan
  • 291 Answers

SOURCE: replace tail light bulb

1. open tailgate. 2. remove corner floor piece by lifting. 3. remove corner side panel. pull out from tab on bottom. 4. remove two hex bolts(#10) to release light housing. they look like large allen wrenches. 5. replace bulb(s) and refasten again.

Posted on May 15, 2008

Ad
  • 1 Answer

SOURCE: replace tail light bulb

open hatch, look for two screws, remove , push tail light gently back and forth to release from clips pull light assembly out , twist bulb socket to remove from housing, replace bulb.

Posted on Sep 19, 2008

eitan
  • 291 Answers

SOURCE: replace tail light bulb

The process for changing the tail light bulbs for a 2002 New Beetle in my case a TDI is relatively simple. To remove the lense and gain access to the bulbs you first need to release the lense holder from inside the trunk by completely unscrewing the large plastic wing nut that is under a round plastic panel that's located almost directly behind the rear brake light lense. To gain access to the plastic wing nut remove the round panel by gently prying it off. After this is done you release the lense by using something flat like a dinner table knife to pry and release the clip that holds the lense in place. Locating the clip: The rear fender has two seams that end at the light lense, the inboard seam (the one closest to the hatch)is where you want to insert the table knife to pry the metal clip that holds the lens in place. Gently and carefully insert the knife blade directly at the seam and pry upward to release the lense. Once the clip releases pull the lens the rest of the way and remove the bulbs by turning the bulb holder sockets couter-clockwise. After this is done remove bulbs by slightly pushing down on the bulb and turning it counter-clockwise. The reinstall is reverse of the removal the procedure.When re-installing take care to clock the lense where the metal clip and the lense protrusions end up in the same position as before. Note: you may need to assist sliding the lens retaining clip in with the knife when reinstalling! Good luck

Posted on May 15, 2008

motor1258
  • 6674 Answers

SOURCE: ABS & Brake light stay on?whats the prob?what needs to be done?£?

Obviously a time for a brake checkover, but if the weather there is snowy & slushy, then perhaps a trip to a carwash & spraying as best as you can behind the wheels, may clean out some debris that may be making one or more of your sensors trip. Not too sure how experienced you are at these type of repairs, as I suspect one or more of your ABS sensors is dirty or faulty, it may be wise to have them checked for safety sake. Be aware that when light is on,ABS may not work, and could allow one or more wheels to lock up when hitting brakes hard in an emergency stop like situation.

Posted on Jan 30, 2009

  • 1986 Answers

SOURCE: replacing tail light bulbs on 2001 Toyota Sequoia

Remove the two screws holding the tail light cover in place along the edge of the tail light assembly.

After you remove the two screws in the back panel, you have to pull the assembly out towards the side of the vehicle. You cannot pull it straight back from the trunk or you will break the pins that hold the lens cover onto the side of the SUV.

There are two pins that allow the light cover to be secured against the back of the truck. One pin is towards the top, the other pin is towards the bottom.

Twist out the bulb assembly.
Pull out the bulb
Insert the new bulb
Twist back in the bulb assembly
Place the pins over the pin holes in the light cover mold on the side of the truck
Push in gently Replace screws and you are done.

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why did my radio and accessory lights go out on my 2001 Chrysler town and country?


On GM vehicles, the dash and accessory lights go out when there is a blown fuse on the tail lights. This design was to get your attention that your driving at night with no tail lights. Most tail light problems are from connecting trailer lights wrong or shorted bulbs/ sockets. This might not apply to Chrysler, but it's something to check.

Aug 06, 2014 | 2001 Chrysler Town & Country

1 Answer

No tail lights, dash lights, signal lights don't work everything else works


sometimes when one of your bulbs is out it does that to all off the start with your turn signal bulbs other wise its you regulater fuse located under the hood

Jan 26, 2013 | 2001 Chrysler PT Cruiser

1 Answer

How to change the tail light?


Hi


Please check the bellow link to have an indepth knowledge to your problem…

http://www.ehow.com/how_6145051_unplug-assembly-2003-chrysler-voyager.html

Let us know if you have something more to know else accept the suggestion.
Thank You for contacting Fixya.com

Jul 31, 2010 | 2001 Chrysler Voyager

1 Answer

How to replace tail light bulbs


replace tail light 2001 voyager

Jan 29, 2010 | 2007 Kia Sedona LX Minivan

1 Answer

Which fuse runs licenes plate bulb and back up lights


THE LICENES PLATE LIGHT COMES ON WITH THE TAIL LIGHTS.IF YOU STILL HAVE TAIL LIGHTS YOU PROBABLY NEED A BULB.

Oct 18, 2009 | 2001 Chrysler PT Cruiser

1 Answer

How do you wire up a trailer harness to a 1999 Grand Voyager?


Your earth is bonding properly. Make sure you have a good bond that is fixed either to your chassis, with all rust, sealent and other cotings are removed frois should dolve your problem.m the fixing. Th

Jul 25, 2009 | 1996 Chrysler Town & Country

1 Answer

Tail lights out but the blinkers and brake lights work. I replaced the bulbs and the fuses are good.


If your front parking lights come on, you have a wiring issue, or body control module issue. If neither front or rear come on, I would suspect the switch.

Jul 10, 2009 | 2002 Chrysler Voyager

Not finding what you are looking for?
2001 Chrysler Voyager Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...