Question about 1994 Toyota Camry

1 Answer

Changed brake shoes...changed master cyclinder.....bled brakes off...brakes remain low to no brakes .....can you help me?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Check for a compressed or collasped rubber brake hose

Posted on Sep 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 23 t bucket and i cant get a brake pedal.when i bought it had very little brake so i replaced rear shoes and cylinders,front pads and calipers,all new lines and the master cylinder


Once you have bled the air from the brake lines,clamp off the front brake hoses carefully.Does the pedal feel better now?
Then the pad /caliper fit is allowing too much play.Is the pedal the same?Then clamp the rear hose and try the pedal.Is it fine with the rear hose clamped?If so we now know the problem is at the rear brakes.One common low pedal rear brake cause is brake shoes that do not fit the drums.Remove the drums and look at the shoes,are they showing contact wear fully or just in the middle of the shoe?Remove a shoe and place it in the drum.Can you rock the shoe against the drum surface?Once drums have been resurfaced,the shoes will not fit fully against the drum allowing the shoe the flex when applying pressure to it and this can easily create a low soft brake pedal. Of course rear brake adjustment must be correct once brake shoe contact is correct.To correct brake shoe contact,have your shoes re arc-ed to fit resurfaced drums or install new drums.Don't overlook brake master cyl /brake pedal push rod adjustment too.

Jun 24, 2017 | Cars & Trucks

4 Answers

Brake pedal goes nearly to floor front pads, calipers, brake hoses changed, rotors turned Master cylinder changed, brake booster check valve changed rear brakes checked, drums good no ridge, shoe's...


I would go with not bled correctly

The booster should hold up with a hard pedal until
you start the engine, then vacuum causes it to move
down when pressing on the brake

Sep 16, 2011 | Saturn SC Cars & Trucks

1 Answer

I replaced disc brake pads, rear shoes. wheel cylinder,master cylinder, power brake booster all new. Question: My brake pedal is not solid,goes low to the floor almost. I have bled the master cylinder 1st,...


Check your lines going to the brakes the rubber hose on the 1993 chevy have a tendancy to crack and brake are you using an excess of brake fluid

Sep 12, 2011 | 1993 Chevrolet C1500

1 Answer

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before...


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Feb 23, 2011 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

Spongy brake pedal even after ABS bleed and base brake bleed.


Did you adjust the rear shoes out? If the rear drum brakes are out of adjustment they will give you a lot of pedal travel. If the pads are worn have no fear of that U-CLIP brake spring, just change one shoe at a time. Take the spring off one side, change the shoe, put the spring back on the post and do the same to the other shoe, no problem.

Dec 03, 2009 | 2001 Chevrolet Venture

1 Answer

N REG POLO changed pads replaced rear wheel cylinder for brake shoes then bled brakes then turn engine on moved car 10ft pressed brake pedal it was like a sponge


You must still have air in one of the pipes - not necessaryily only to the wheel you have been working on (though normally that is so). Did youu make sure that the fluid level remained above minimum in the brake fluid master cylinder while you were bleeding the brakes? Possibly a slurp of air went in there and now the other pipes will need bleeding too. Don't panic - just bleed all the brake pipes, making sure that the master cylinder level stays high.

Sep 26, 2009 | Volkswagen Golf Cars & Trucks

2 Answers

No brake pedal


first check your brake fluid. It may be low. Having low fluid could have also led to getting air in the brake line. You may need to have your brakes bled. Its not that expensive probably 50-60 bucks at your local garage.

Feb 02, 2009 | 1985 Toyota Pickup

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...