Question about 1993 Toyota Tercel

1 Answer

I have a 93 tercel 4 cylinder running on 3 what do i have to do to make it run on 4 cylinders again and how much will it cost

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Replace the cap, rotor, wires , and spark plugs. Unless there is something serious happening with the motor , this should get you up and running again. Should only cost about $50 or so.

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 xlt 580. Only runs on 2 cylinders sometimes at cold. Change plugs and works sometimes.. Not always same cylinder.. Any way to check stator,coil?


Ask The SnowMan Your Sledding Questions Answered: Off ...

www.off-road.com/.../ask-the-snowman-your-sledding-questions-answer...
Mar 1, 2009 - Its a 96 polaris indy xlt 600 triple not the special edition though. ... THEM SITTING ON THE HEADS BUT ONLY 2 CYLINDERS ARE RUNNING WHEN ... Q: I have a arctic cat ext580 the compression in both cylinders is about 70psi .... i have a93 polaris 600 xlt and I just got home and the antifreeze is ...

93 XLT Carb settings? - Snowmobile Forum: Your #1 Snowmobile Forum

www.snowmobileforum.com/polaris.../41045-93-xlt-carb-settings.html
Nov 27, 2009 - I bought a new to me 95 polaris sport last year. it had not run in twoyears. ... It's all in the tuning, clutching, jetting and gears.. i have a 93 xlt 580 and i ... he is loading up with fuel and just cutting the spark out of a cylinder.. i had ... XLT w/ Triple Pipes Question?
May 8, 2013
93 XLT Ran Great, Shut Down, Now Backfires
Feb 13, 2012
Dead cylinder
Dec 11, 2011
1998 ski doo f3 700 wont run right
Feb 22, 2011
More results from www.snowmobileforum.com

Polaris Indy 600 XLT HELP! - Snowmobile Fanatics


Jan 04, 2016 | Cars & Trucks

1 Answer

No compression in one cylinder in a 1993 Toyota tercel


Could be a burnt valve or bad set of piston rings on that cylinder. Probably would be more feasible to replace the engine with a lower mileage one.

Feb 23, 2015 | 1993 Toyota Tercel

1 Answer

3/4 tonne ford 4x4 93 clutch has no give can't


Had a 92 Ford 3/4 ton 4x4. And the same problem. I changed the clutch master cylinder, slave cylinder (inside of bellhousing), Disc. pressure plate, & throwout bearing. Cost some money but it was worth it. Never had another problem.

Aug 23, 2013 | Cars & Trucks

1 Answer

93 altima.running on 3 cyliners, spark to ALL 4 CYLINDERS, BUT 1ST CYLINDER, not firing. Maybe fuel injector???


CYLINDER 1 COULD HAVE A BAD FUEL INJECTOR.OR SHORT IN THE WIRING TO 1 FUEL INJECTOR.

Mar 04, 2011 | 1993 Nissan Altima

1 Answer

'93 Grand Am only running on 2 cylinders


The common repair for the "running on 2 cylinders" is the coil pack with ignition wires.
It sits on top of the engine.
A good used one will work just as well as a new one......but at 1/2 the cost.

Sep 05, 2009 | 1993 Pontiac Grand Am

1 Answer

Change key cylender on 93 bronco


You need to remove the Steering wheel.
Remove trim shrounds.
Set ignition switch to Run position.
If your vehicle is A/T trans. put the selector lever in Park.
You will see retaining pin. Push retaining pin inward and pull out the lock cylinder.
Unplug wire from lock cylinder.
To install reverse remove procedure.

NOTE'' If you don't have the key or the cylinder is locked.
Instead of push the retaining pin you will need to Drill with a
1/8 in ( 3.17mm) Bit to drill out the retaining pin.
Be careful DO NOT drill more than 1/2 in deep.
After you need a chisel to break away the cylinder cap.
You need a 3/8in (9.52mm) bit to Drill in center of the cylinder.
Drill aprox. 1 3/4 in( 44mm) Deep.
REmove metal shavings. And remove the cylinder.
Clean and lubricate the gear inside. and install the new cylinder

Apr 29, 2009 | 1993 Ford Bronco

2 Answers

93 oldsmobile quad 4 2.3 one piston is not working wet spark plug


If you have a stethoscope, listen to the injector while the vehicle is running, it could be stuck open. If you hear it pulsing the same as the rest of the injectors, then unplug it, let the engine run so it can get all of the unburned fuel out of cylinder (you said the plug was wet), take the plug and coil from cylinder number three, install them in cylinder # 4, put the coil/plug from 4 into 3, reconnect the injector, and see if the problem moves to cylinder three. Next if the problem does not move to cylinder 3, then you have an issue with either the wiring to the connector at cylinder # 4, or you have a mechanical failure. Remove the valve cover, check the valve springs on # 4. make sure they look the same as all others. If so, turn the crank and further inspect them. If they are mangled, remove the head. It needs to be repaired, and check the piston for damage. You could also do a compression check to rule this out.

Mar 27, 2009 | 1993 Oldsmobile Achieva

1 Answer

Ignition key cylinder


You have to have the ignition lock exposed, take the covers off above and below the lock body that holds the cylinder.
Insert the key fully into the keyway, and turn it to ACC. On the ignition lock body, press on the "stop pin", that pokes out of the lack body, above where the cylinder is housed. Press on the "stop-pin", and extract the cylinder. If the key can not be turn ed to ACC, the cylinder will not come out.
Thanks for choosing FixYa. Please let me know if this solves your problem.

Dec 16, 2008 | 1993 Toyota Tercel

Not finding what you are looking for?
1993 Toyota Tercel Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...