Question about 1995 Cadillac DeVille

1 Answer

How do I fix a broken pully on a water pump? - 1995 Cadillac DeVille

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Remove the belt then remove the 4 water pump pulley bolts.
reverse this procedure to install

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a ford KA 1999 and the pully wheel on the water pump has broken off the pump. I have unscrewed the water pump but i carn't get the water pump out of the engine.


ok u have to go to the a auto zone and see if they can rent u a PULLY TO UPLL IT OUT OR A PEP BOYS THAT RENTS TOOLS

Nov 29, 2013 | 2000 Ford Ka

1 Answer

Need to locate and replace the water pump on 1997 nissan sentra.


The water pump is located on the passanger side of the engine. Look right below the timing chain cover and there is a pully and belt on the water pump. You will have to remove the water pump and thermostate together then seperate them after you get them off the car. I would recommend replacing the thermostate also (cheap fix). You will have to remove the belt and pully before you can remove the water pump. Hope this helps....

Jan 05, 2013 | 1997 Nissan Sentra

1 Answer

I installed a new powersteering pump on a 88 gmc k1500, now it eats serpentine belts cant get the pullies lined up right how do i fix?


I would install a reman pump,never try & remove a pully
The pump wasn't the problem

Your problem is most likely that the crank damper has
worn & moved. The rubber in it is the issue & it is hard
to see any misalignment

Jun 13, 2012 | Cars & Trucks

1 Answer

Whaere is the water pump located


The water pump is on the top right hand side of the engine if you standing on the passenger side looking at the front of the engine. Keep in mind that the water pump only goes back on one way, so make sure that you have it clocked right or the bolts wont line back up. Remove the water pump pully first before you take the belt off. This makes it easier to break the pully bolts loose and then remove the water pump bolts. Then after, put the pully back on and then the belt and then tighten the pully bolts, the belt will help hod the pully for you.


360dreamworx_44.gif
360dreamworx_45.gif
360dreamworx_46.gif

Aug 08, 2011 | 2003 Buick Rendezvous

3 Answers

Colant lose at right side of 3800 eng. 1994 park ave visable about half way down side below pully.


Most likely water pump. Might be broken plastic heater hose elbow, lower intake to belt tensioner. They tend to become brittle with age.

Sep 27, 2009 | 1994 Buick Park Avenue

1 Answer

Newly replaced timing belt was broken in my daewoo nubira 2000


Yes you should always do the water pump when doing the timing belt. belt tension too tight can cause the break as well as a bad water pump or idler pully, these should all be replaced when you do a timing belt to save yourself this exact headache later on.

May 12, 2009 | 2000 Daewoo Nubira

1 Answer

The pully on my water pump is lose


The pulley on the water pump is separate from the pump on both the 6 and V-8 engines (you didn't specify which engine was in your truck).
If the pulley is wobbling around and grinding, the bearings have failed on the pump. The fact that it has not leaked is not unheard of. REPLACE THE PUMP! Continued operation will cause the impeller (the side of the pump which moves the water) to chew up the housing. Not to mention leaving you stranded.

Apr 06, 2009 | 1998 Dodge Durango

2 Answers

Lancer cedia 2001 4g93 1800cc is overheating. What tests do I carry out to check if its the water pump or thermostat


all engine overheating is du to malfunctioning cooling parts or coponents in the engine or attached to engine or car ... first ck for leak , coolant or water leak , then ck if the thermostat open on time to let the waterpass trhu ck the cooling fans if they working propely and kick on time , ck for an cloged radiator that neded to be fluch up nicolas

Dec 20, 2008 | 2005 Mitsubishi Lancer

Not finding what you are looking for?
1995 Cadillac DeVille Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...