Question about 1999 Chrysler Town & Country

1 Answer

How to replace a heater fan motor, is it changeable from the engine compartment?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 8,267 Answers

No, but it isn't too hard to get to under dash. I will paste instructions from autozone.com below. Pictures may not come thru.

CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
Front Blower Motor
See Figures 1, 2 and 3



How to replace a heater fan motor, is it - 0900c1528003c5cf.jpg enlarge_icon.gif

Fig. Fig. 1: The blower motor is located behind the glovebox, behind the blower motor cover

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel.
  3. Remove the A/C-heater blower motor cover.
  4. Disconnect the blower motor wiring connector.
  5. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  6. Remove the blower motor mounting sHow to replace a heater fan motor, is it - 0900c1528003c5d0.jpgi>




0900c1528003c5d0.jpg enlarge_icon.gifenlarge_tooltip.gif enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.

To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 buick lesabre the blower motor keeps running after car is turned off


if you are talking about the engine electric cooling fan..it will run after car is turned off until temp goes down then it shut off..unless you're talking about the heater blower motor..then i would look in the engine compartment passenger side firewall for the heater box ..on the box there is speed control resistor for the heater fan speed..that might be shorted.if not fan switch on dash..give more info next time..it makes it easier answer with more info

Sep 21, 2010 | Buick LeSabre Cars & Trucks

1 Answer

How do i replace heater moter


For 4.0L, inside the engine compartment, on the passenger side firewall, remove the coolant overflow bottle retaining strap remove the coolant overflow bottle and bracket. Unplug the blower motor. Remove the 3 blower motor bolts.Remove the blower motor. Remove the blower motor fan from the motor shaft for access to the motor attaching nuts. For the V-8, you just need to unbolt the blower motor to remove.

Mar 16, 2010 | 1996 Jeep Grand Cherokee

3 Answers

Heater motor only wokks on high


probley the restor that gives the a/c heater fan motor its power for the low/ medeam speds has gone bad and onley letes it run on high speed because it gives the fan motor full battery voltage on high speed. it should be located in the heater box were the fan will blow air across it to cool it when it is in use GEORGE STIRBER DBA AUTO ENGINEERING

Jan 01, 2010 | 2001 Nissan Xterra

2 Answers

Heater fan only runs on high setting


Hello...

Try replacing the blower resistor. It is usually located in the engine compartment near the blower motor.

Good Luck...

Dec 16, 2009 | 1997 Chevrolet Cavalier

1 Answer

Where is the blower motor on a 93 nissan altima


If you mean the heater fan motor it's usually in the engine compartment bolted to the fire wall. You replace in from there, not from inside the car. It's right behind the heater coil. It's probably behind a round metal plate, about the size of a saucer bolted to your firewall. Real easy to swap out.

Nov 29, 2009 | 2000 Pontiac Grand Prix

1 Answer

I am getting in heat... We know it now the heating core... Do you have any idea what it is


If it isn't the heater coil, then the only things left are the heater fan fuse or the heater fan motor itself. Check your fuses. If you don't have a fuse diagram, start with highest amp fuses first. The heater motor uses a lot of juice and will probably be on at least a 10 amp fuse. If all the fuses are good then you probably need a new heater fan motor. They usually mount to the fire wall from the engine compartment and are pretty easy to change. Not at all like the heater coil.

Nov 29, 2009 | 1997 Ford Explorer AWD

1 Answer

The heater fan blows fuses when it's turned on.


remove the power wire to the blower motor usually on firewall in engine compartment and replace the fuse then switch on, if fuse doesn't blow with motor disconnected then you'll know its the motor

Oct 09, 2009 | 1996 Plymouth Neon

1 Answer

2004 crown victoria heater fan not working, fuses OK. motor OK Power at motor, No ground at motor. Is the problem a resister.


You are most probably correct, fan motor resistor is usually found at the top center of firewall in engine compartment.

Aug 02, 2009 | 1989 Ford Crown Victoria

1 Answer

Heater fan on 1992 GMC Sierre


It could be sticking or may be corrosion on the wiring or the motor but in order to replace it, you need to remove the cover from in the engine compartment and take it out that way. Make sure you use a new seal or sealer around the cover when putting it back on.

Feb 27, 2009 | 1992 GMC Sonoma

1 Answer

IM TRYING TO CHANGE MY HEATER CORE ON AN 01 S10. I HAVE THE DASH OUT BUT CAN'T FIGURE OUT HOW TO GET THE CASE OFF OF IT.


on the out side of cab under hood in engine compartment on the firewall there are 2 nuts that need to be removed and 1 by the heater fan motor. theres a little secret trap compartment in engine compartment by the ac unit and the heater core fan that has 3rd bolt. the box on the inside of cab will come lose.

Jan 09, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
1999 Chrysler Town & Country Logo

738 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...