Question about 2001 Hyundai XG300

Open Question

How to remove rear brake rotor from 2001 hyundai xg300

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1280 Answers

SOURCE: how to remove brake drum rear wheel 2004 Hyundai Elantra

Jack up rear of car till tire is off the ground.
Remove lug nuts & remove wheel.
Remove phillips screw(s) from drum.
Using a hammer, strike the drum to loosen it from the hub.
Remove drum by simutaneously turning it and pulling it outward away from the vehicle.

Posted on Oct 04, 2009

  • 105 Answers

SOURCE: 2003 hyundai elantra brake rotor removal

if there are screws holding rotor on remove can drill the heads of if you need to they realy dont do any thing remove caliper bracket if its in the way some rotors have drilled and taped holes in them if yoursn do thread bolts into them and tighten down this will put pressure on the rotor to pushit of hub if not use large hammer and hit the face of rotor between studs to loosen it up also dont be afraid to use lots of wd40 of so sort of penatrating oil on them to help loosen them up let me know how you make out

Posted on May 31, 2009

  • 776 Answers

SOURCE: brake rotors for hyundai accent

The rotor is mounted to the hub by 4 bolts. The procedure is described in the service manual. Go to and register. You'll have access to the information you want after you register (shop manual, wiring diagrams, service bulletins, etc.).

Posted on May 28, 2009

  • 776 Answers

SOURCE: replacing 2001 Hyundai XG300 headlight, how difficult?

1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.


Posted on Jun 20, 2009

  • 1071 Answers

SOURCE: 2001 Hyundai XG300 with an engine light (p0715/P1159)

clean up all ground wires but you may need both of those items

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i bleed the brakes on a 2001 hyundai xg300l with ABS

Start at the right rear and have someone pump the breaks till hard to pump. than on the wheel cylinder there is a 8mm bleeder. Crack that open till notin comes out. Repeat 2 or 3 times than move to the left rear and repeat. REMEMBER while doin the frequently check break level..

Mar 07, 2012 | 2001 Hyundai XG300

1 Answer

Where is the vehicle speed sensor located on my hyundai 2001 xg 300

It should be located beside the brake caliper either on front or rear wheels (not sure about side but surely on both wheels) will look like a small tube pointing towards the hub.

Sep 30, 2010 | 2001 Hyundai XG300

1 Answer

Trying to remove and replace the right rear wheel bearing on a Hyundai xg 300 2001 model

you have to remove the caliper first than your disk brake(this is a hub assembly) on the back of the weel bearing you should have 3 big bolts remove them put a chain on 2 of the stud of the weel put back the nut on them (if you don't have the tool to do it)than take a steel bar and do like a (slege hammer) just few hit it should come out!..hope this will help you. lipak!...

Mar 29, 2010 | 2001 Hyundai XG300

1 Answer

Left rear brake light won't work with new bulb

Go to and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Apr 24, 2009 | 2001 Hyundai XG300

1 Answer

Which way do the spark plug wires go on the spark plug cylinders?

yes it does matter, big time.

You start by putting the spark plug wire for #1 on the distributor, on the #1 spark plug. #1 is usually the first plug in the rear on the passenger side. Then figure out which way the rotor rotates, usually clockwise. Then put the plug wires on in the order of the firing order. It is not in numerical order.

If you did not take them off already, just do one at a time.

Apr 19, 2009 | 2001 Hyundai XG300

1 Answer

How to adjust handbrake 2001 hyundai grandeur xg

remove back wheels with screendriver adjust handbrake remove rubber plug from disc brake rotate disc brake down and look inside the disc with light;ask other people with ML (mercedes) ,JEEP,GM

Feb 26, 2009 | 2001 Hyundai XG300

1 Answer

Changing rear brake discs

Please follow this link
There is step-by-step infor how to change brakes
Kindly let me know if you need more infor or link doesnot work
Good Luck

Feb 13, 2009 | 2001 Hyundai XG300

1 Answer

I have a 2001 Hyundai XG 300. I replaced the front brake pads and rotors and now have no pedal. When I try bleeding the brakes (engine off or on) no fluid comes through the bleeders. Do you think it is a...

leave the bleeder open for a hour and remove the master cap,soon or later it's gonna leak when there's no more air it's gone leak nice if that d'oesn't worck i will go for a bad master.

Jul 18, 2008 | 2001 Hyundai XG300

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides