Question about 1996 Honda Accord

1 Answer

How do I remove the distributor rotor on my 1996 Honda Accord?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,478 Answers

Hello,

In order to get the set screw in a position so it can be easily removed, you have to get the rotor to rotate. Act as if you are going to start the car, but only hold the key in the start position for a split second. The cars engine will turn over, and the rotor will rotate, hopefully to where it is easier to get the screw out. If not, try again.

Take care.

Posted on Sep 15, 2010

Testimonial: "I have tried that solution several times but it is a hit or miss situation."

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 255 Answers

SOURCE: how do i remove the rotor for a 1990 honda accord

remove caliper, caliper bracket it may or may not have a screw that holds it to the hub pretty easy actually

hope2help

Posted on Apr 17, 2009

csmock132
  • 4669 Answers

SOURCE: Leaking oil from distributor (small amount of oil)

Is it leaking arond it? Replace oring seal. Is it leaking from where the cap seals the the distributor? Replace the distributor.

Posted on May 07, 2009

  • 77 Answers

SOURCE: 1996 Honda Accord Rough Idle Even After tune up

Perform a valve clearance inspection and adjust if necessary. Tight or sticking valves will cause a misfire or rough running concern. Note: Perform valve adjustment when the engine is stone cold. 4cyl: INT 0.26mm EXH: 0.30mm (V6 engine are hydraulic and no adjust necessary.) Also check for a sticking or stuck open EGR valve. For diagnostic purposes only: Remove the EGR valve. Place a business card over the EGR passage and bolt the EGR valve back on. This plugs the EGR ports and if the misfire goes away the EGR valve is partially stuck open and is defective.
Check for low fuel pressure. Check for low compression. Check cam timing. Check for a weak ignition coil. Also don't over look the possibility of worn or broken engine mounts which cause excessive engine movement and engine vibration. -hope this helps

Posted on Mar 05, 2010

1ATony
  • 159 Answers

SOURCE: remove rotor from distributor cap on 1993 honda

Here's a great video that will show you how to remove the distributor on your Honda Accord.">

Posted on Jan 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 accord will not start has no fire to plugs


start with a new distributor cap and rotor button. Should probably replace the plug wires too. If still nothing, look to see that you're getting spark from the coil to the distributor.

Dec 28, 2013 | 1996 Honda Accord

1 Answer

MY 1996 honda accord has fuel but no spark


Check Ignition system:
- Distributor cap, rotor, wires.
- Ignition coil.
- Ignition module.
- Distributor.

Apr 21, 2013 | 1992 Honda Accord

1 Answer

96 honda accord misfire under hard acceleration


has it had a tune up. spark plugs ,wires and rotor and distributor cap. Are there any codes on

Oct 30, 2012 | 1996 Honda Accord

1 Answer

What is the spark plug/distributer firing order for a honda accord 6 cylinder engine?


The 2.7 L - V6 engine in a 1996 Honda Accord is : 1 - 4 - 2 - 5 - 3 - 6 The distributor rotor turns COUNTER-CLOCKWISE
The engine cylinders / spark plug locations are numbered :
1----2----3
4----5----6
front of Accord




Oct 31, 2010 | 1996 Honda Accord

1 Answer

I JUST REPLACED THE DISTRIBUTOR HOW CAN I PUT MY 1996 HONDA ACCORD WITH 2.2 V-TECH ENGINE BACK ON TIME


You'll need to get piston number one at top dead center. Mark on the distributor housing to line up with the number one tower of the distributor cap. When you install the distributor, line up the rotor with the mark on the distributor. Here is also a link with more information that should help you:
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528003a03b

Oct 31, 2010 | 1996 Honda Accord

1 Answer

Remove rotor from distributor cap on 1993 honda accord ex


Here's a great video that will show you how to remove the distributor on your Honda Accord.">

Jul 21, 2010 | 1993 Honda Accord

1 Answer

How to remove and install a distributor on a 1993 honda accord?


1. remove the distributor cap and rotor, don't remove the spark wires. 2. unplug the wire from the distributor. 3. remove the distributor bolts, pull the distributor out. When install the distributor make sure replace the new O ring.

Apr 09, 2010 | 1993 Honda Accord

1 Answer

How to change ignitor on 1991 honda accord


Honda has 2 distributors, Hitachi (with an internal ignitor) and Toyo Denso (with an external mounted ignitor). The toyo denso is removed by removing 2 bolts and a harness clip on the outside of the distributor. The Hitachi requires that you remove the dist. cap, rotor, and 'reluctor', which is under the rotor, the ignitor is under that, remove the retaining screws, make sure the screws are put back in the same locations, as one is a 'diamegnetic' screw, and must be replaced in the correct location.

Nov 16, 2009 | 1991 Honda Accord

2 Answers

1996 HONDA ACCORD HOW DO I REPLACE THE FRONT ROTORS


  1. the rotors are held on by the wheel mainly
  2. to replace remove wheel
  3. remove caliper
  4. if brake pad cage raps around rotor remove with 2 bolts from backside
  5. take big hammer and tap surface of rotor near wheel studs use care not to hit studs. one or two good smacks should break rotor free from rust

Nov 15, 2008 | 1996 Honda Accord

1 Answer

96 honda accord Removing brake rotor


hi remove the the rotors retaining screws then remove the two bolts holding the caliper and pull it out of the way take the rotor off yates210456

Oct 01, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...