Question about 2006 Nissan Altima

2 Answers

P 2138 code with service engine soon light on?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

Accelerator Pedal Position Error.

P2138 - Accelerator Pedal Position Sensor Circuit Range / Performance Problem

Clear the code - if it recurs, change the sensor.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 15, 2010

  • blueextc3221
    blueextc3221 Sep 15, 2010

    If i may....

    1 Thumb ratings are reserved for answers that are abusive, threatening, etc.

    What about my answer is any of that?

    You got the exact diagnosis you were looking for... did you have a follow-up question?

    Do you need absolute PROOF the DTC is what I have listed it as?

    Please re-consider your rating - as most experts here answer free questions, and our rating is our only source of satisfaction for doing so. 1 Thumb rating tend to sting a bit - especially with no explanation.

    Thanks!!

  • Gary Altonot
    Gary Altonot Aug 27, 2015

    That explanation is pretty spot on from what I've been able to find searching the internet for several hours.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 22,156 Answers

NISSAN OBDII DTC

P1105 Manifold Absolute Pressure/Barometric Pressure Switch Solenoid Circuit

P1110 Intake Valve Timing Control Circuit (Bank 1)

P1120 Secondary Throttle Position Sensor Circuit

P1125 Tandem Throttle Position Sensor Circuit

P1132 Intake Valve Timing Control Position Sensor (Bank 1)

P1135 Intake Valve Timing Control Circuit (Bank 2)

P1137 Intake Valve Timing Control Position Sensor (Bank 2)

P1140 Intake Valve Timing Control Position Sensor (Bank 1)

P1145 Intake Valve Timing Control Position Sensor (Bank 2)

P1148 Closed Loop Fault Detected (Bank 1)

P1168 Closed Loop Fault Detected (Bank 2)

P1210 Traction Control System Signal Fault

P1220 Fuel Pump Control Module Fault

P1320 Ignition Control Signal Fault

P1335 Crankshaft Position Sensor Circuit

P1336 Crankshaft Position Sensor circuit

P1400 EGR/EVAP Control Solenoid Circuit

P1401 EGR Temperature Sensor Circuit

P1402 EGR System Fault Detected

P1440 EVAP Canister System Leak Detected

P1441 EVAP Vacuum Cut Valve Bypass Valve Circuit

P1443 EVAP Canister Control Vacuum Switch Circuit

P1444 EVAP Canister Purge Volume Control Valve Circuit

P1445 EVAP Purge Volume Control Valve

P1446 EVAP Canister Vent Valve Circuit

P1447 EVAP Canister Purge Flow/Volume Control Valve Circuit

P1448 EVAP Vent Control Valve Circuit

P1490 EVAP Vent Control Valve/Bypass Valve Circuit

P1491 EVAP Vacuum Cut Valve/Bypass Valve Circuit

P1492 EVAP Canister Purge Control Valve/Solenoid Valve

P1605 Transmission Control Module A/T Diagnosis Communication Line Fault

P1705 Throttle Position Switch Circuit

P1706 Park Neutral Position Switch Circuit

P1760 Overrun Clutch Solenoid Valve Circuit
P1900 Cooling Fan Control Circuit

Posted on Sep 15, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

racefan966
  • 14 Answers

SOURCE: service engine soon light P1152 code

Most likely a one of the o2 sensors are causing this problem. What you need to do is a get a repair manual and do some pin tests on the O2's and figure out which one is faulty.

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I change the App on a 2008 Acura tl and the check engine light came back with the same codes p2138 p2122 what else can cause the codes to come back on


code p 2138 refers to throttle position (TP) sensor/switch D/E-- voltage correlation=== causes --- wiring -- tp sensor /switch

code p 2122 refers to accelerator pedal (APP) sensor /switch D --low input===causes --wiring short to ground --APP sensor/ switch

also refers to engine control module (ECM) , idle control ---high input===causes ---wiring short to positive --TP sensor--ETS control valve (ETS----electronic throttle system)

Jan 10, 2017 | Acura Cars & Trucks

2 Answers

How to reset Service Engine Soon light after replacing gas cap? Took to AutoZone when the Service Engine Soon light came on Error code P0440.


Disconnect the negative battery cable for 30 minutes. Reconnect after and the code will clear. However if the problem persists, the code will come back with in 20 miles or 30 minutes.

Aug 02, 2014 | 2000 Buick Regal LS

1 Answer

Engine Service Soon Light On code P0154


Error Code: P0154
Description:
Heated Oxygen Sensor (HO2S) 1 , Bank 2 - No Activity Detected
Problem areas:
- Wiring.
- Open circuit in signal wire, between Heated Oxygen sensor 1, Bank 2 and ECM. (Must check and confirm)
- Heated oxygen sensor (HO2S).
- Engine control module (ECM).

Nov 20, 2013 | 2003 Mitsubishi Montero Sport

1 Answer

I have a 2001 mustang bullitt that is showing service engine light on. Took it to mechanic and he put 2 different machines on it to show code for problem. No codes coming up and he can't turn off the...


There is a diagnostic procedure in the factory service repair manual for engine light lit ,no codes . Did you take it to ford dealer ? MIL - is referring to check engine , service engine soon etc...
  • MIL always on when engine is running (no DTCs):
  • MIL circuits
  • For Focus, Mustang, Town Car, Continental, LS6/LS8, Escape, Windstar, F-150, Expedition and Navigator/Blackwood:
  • Instrument Cluster, Section 413-01 of the Workshop Manual.
  • All Others:
  • GO to NB1

SERVICE ENGINE SOON indicator After the engine is started, the SERVICE ENGINE SOON indicator will prove out for a duration of three seconds. If the instrument cluster does not receive a message from the PCM within five seconds, the instrument cluster will illuminate the SERVICE ENGINE SOON indicator and log a diagnostic trouble code (DTC).

  • An indicator is inoperative/always on - SERVICE ENGINE SOON
  • Circuitry.
  • Bulb.
  • Instrument cluster.
  • PCM.
  • GO to Pinpoint Test P .

PINPOINT TEST P: AN INDICATOR IS INOPERATIVE/ALWAYS ON - SERVICE ENGINE SOON CONDITIONS DETAILS/RESULTS/ACTIONS P1 CARRY OUT THE INSTRUMENT CLUSTER SERVICE ENGINE SOON INDICATOR ACTIVE COMMAND Trigger the HEC active command MIL.
  • Did the SERVICE ENGINE SOON indicator illuminate?
Yes REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual.

No INSTALL a new instrument cluster; REFER to Instrument Cluster . CLEAR the DTCs. REPEAT the self-test.

Jul 18, 2017 | 2001 Ford Mustang

1 Answer

1998 Ford Escort - P1405 Error code


Follow the link for help with this fault code P1405 Ford DPF EGR Sensor Circuit High Voltage Detected

I suggest you replace the EGR valve position sensor.

Mar 10, 2017 | 1998 Ford Escort

1 Answer

Two service engine lights


one is service engine soon referring to the engine and trans. systems, and one is service vehicle soon, referring to body, abs, hvac, etc. systems two different lights for 2 different types of trouble codes

Mar 17, 2010 | 2002 Pontiac Grand Am

3 Answers

Dies when started cant find check engine light


The service engine light is the check engine light. Different name for the same thing.

Feb 22, 2010 | 2002 Ford E350

1 Answer

Why does my tahoe keep displaying reduced engine power? The drivetrain and traction control lights also came on.


There is a service bulletin for this concern.The number is 07-06-04-019A.It has to do with the body harness instrument panel connector.It is on the left hand kick panel area inside the instrument panel.You should have the codes checked.You will probably have a P 2138 code.This is for the accelerator pedal position sensor 1 and 2 correlation.Hope this helps.

Dec 19, 2009 | 2005 Chevrolet Tahoe

2 Answers

Check eng light is on


Most common problem for 0449, and 0455 on this truck is dust in evap vent valve causing valve to stick open and resulting in 0455
need to replace evap vent valve and clean dust from vent hoses

Jul 07, 2008 | 2006 Chevrolet Silverado 1500 2WD

Not finding what you are looking for?
2006 Nissan Altima Logo

2,835 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...