Question about 2004 Renault 181

1 Answer

Hi fault code cam to crank sincro out but timming spot on engine does evrything but start from key bumps easy starts with a sniff of carb cleanner but no otherway weather hot or cold thanks phil

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Renault Master
  • 22,156 Answers

Well forget the fault code reading this is a renault remember and you are lucky if you can get the vin number up ,now i had this fault before with a renault ,and i cant remember what i did ??? i think it was the vacumn pipe on the shut off valve on the fuel rail ,it was perished or split or something stupid

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I was driving my 1994 isuzu rodeo and lost complete power.Got a few jumps and truck wont start.sounds like it wants to start when i turn key over.I also put gas in and still nothing


run the fault codes
check for cam/crank position sensors failure, immobilizer failure , pump operation
could be a failed ECM
have the battery load tested as it may be the original fault and jump starting may have caused a power surge and damaged the ECM

Feb 27, 2016 | Isuzu Cars & Trucks

1 Answer

Transit van will not start of the key


What is the model year, is this a Pontiac? If your saying the starter motor cranks good but won't start, then have helper crank it while you check for spark--fuel--injector pulse.
If your theft/ security system has a problem, that is another issue.
I'm not totally sure I understood your post?

Dec 22, 2015 | Cars & Trucks

1 Answer

Engine will not start


run fault codes to check for cam./ crank sensor faulty Check immobilizer and fob key battery. Check that the cam shaft is turning over (broken timing belt)

Oct 26, 2013 | Ford Cars & Trucks

1 Answer

I HAVE A 2005 YARIS WITH A 1KR-FE ENGINE. IT WAS OVERHAULD BY A TOYOTA DEALER NOW THE CAR WONT START. THE CRANK SENSOR AND THE CAM SENSOR ARE NEW. THE ENGINE LIGHT IS ON. WHEN THE DIAGNOSTIC MACHINE IS...


check that the cam sensor rotor is on the camshaft properly and is adjusted to the correct air gap
if the dealer just did the overhaul then take it back to them

Oct 08, 2013 | 2007 Toyota Yaris

1 Answer

My 2002 Kia Sedona won't start?


There is something wrong with the glow plug circuit and it needs to be troubleshooted using a wiring diagram

Aug 15, 2013 | 2002 Kia Sedona

1 Answer

Timming belt routing on 2002 montero xlt 3.5 engine vin code R 6g74 This car came in to me with the complaint that it starts fine cold but after it warms up the engine turns over a few times then...


The Marks are different (ie 12oclock/11:30 or so) as pictured here. I will post again if it is too small to read (sometimes fixya shrinks pictures)

4c8e43c.gif

Nov 08, 2009 | 2002 Mitsubishi Montero

1 Answer

Cranks, but no start. spark and fuel good, no


cam timming is possibly out due to gear reduction set up in heads
suggest remove rocker covers and make sure cam lobes are in this possition as well as all other timming marks luckily these engines (V6) are free wheeling (wont bend valves) set up like pic below

5b1d17c.jpg

Nov 03, 2009 | 1998 Isuzu Trooper

3 Answers

1998 suzuki esteem 1.6 will not start HELP!


Having good fuel pressure is a plus (yours seems a bit high but I don't have specs) What you need to find out is if the injectors are opening and putting the fuel into the engine so it can work. Are the plugs wet with fuel or dry? Does it fire up if you spray carb cleaner into the throttle body while cranking?

Aug 30, 2009 | 1998 Suzuki Esteem

Not finding what you are looking for?

Open Questions:

See all 2004 Renault 181 Questions

Cars & Trucks Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4861 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...