Question about 2003 Mazda MX-5 Miata

Open Question

P2404 , leak detection pump - 2003 Mazda MX-5 Miata

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 11122 Answers

SOURCE: Evaporative Emission System codes

check ur gas cap for tight and proper seal that is the most common problem for the the evap codes if cap is good check fuel and vent lines for damage or leaks from gas cap under vehicle up to engine compartment

Posted on Oct 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.3l engine. What are the probable causes of DTC P1495?


answer courtesy of engine codes .com Engine-Codes OBDII Code List P1495 Dodge
P1495 Dodge P1495 Dodge - EVAP Leak Detection Pump Solenoid Circuit Condition 3 ' Add Comment Possible causes
- Faulty Leak Detection Pump (LDP)
- Leak Detection Pump (LDP) harness is open or shorted
- Leak Detection Pump (LDP) poor electrical connection
What does this mean? When is the code detected?
Malfunction is detected when the Powertrain Control Module (PCM) detected the pump solenoid did not change status when activated,
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors
P1495 Dodge Description
The Evaporative emissions system is design to prevent the escape of fuel vapors from the fuel system. Leaks in the system, ca allow vapors to escape into the atmosphere. The leak detection system tests for EVAP system leaks and blockage.
During the self-diagnostics, the Powertrain Control Module (PCM) first checks the Leak Detection Pump (LDP) for electrical and mechanical faults. If the first checks pass, the PCM then uses the LDP to seal the vent valve and pump air into the system to pressurize it. If a leak is present, the PCM will continue pumping the LDP to replace the air that leaks out. The PCM determines the size of the leak based on how fast/long it must pump the LDP as it tries to maintain pressure in the system.

Read more: http://engine-codes.com/p1495_dodge.html#ixzz3iQ8P3JII P1495 Dodge EVAP Leak Detection Pump Solenoid Circuit Condition

Aug 10, 2015 | Dodge Caravan Cars & Trucks

1 Answer

What is a P2404 code mean from a suzuki sx4


Trouble Code: P2404 (2.0L L4 VIN 5 Automatic CVT)
Evaporative Emission System Leak Detection Pump Sense Circuit Range / Performance
Number of Trips to Set Code: 1
Trouble Code Conditions:
EVAP vent valve stuck open: EVAP leak check pressure is lower than -0.14 kPa even if EVAP vent valve is operated from OFF (OPEN) to ON (CLOSE) with EVAP leak detection pump ON. EVAP vent valve stuck closed: EVAP leak check pressure is unstable (difference between maximum and minimum is 0.36 kPa or more) when EVAP vent valve is OFF (OPEN) with EVAP leak detection pump ON. EVAP leak detection pump stuck OFF: EVAP leak check pressure is higher than -0.14 kPa even if EVAP leak detection pump is ON. EVAP leak detection pump flow high: Reference pressure of EVAP leak check pressure is lower than specified value (depending on BARO) EVAP leak detection pump flow Low: Reference pressure of EVAP leak check pressure is higher than specified value (depending on BARO).
Possible Causes:
  • EVAP leak detection pump (in EVAP leak check module) and/or its circuit
  • EVAP vent valve (in EVAP leak check module) and/or its circuit
  • EVAP leak check module and/or its circuit
  • ECM

Jul 11, 2014 | 2010 Suzuki SX4

1 Answer

Where is the location of code p1495 leak detection pump solenoid circuit


The Solenoid circuit is part of Emission control.To get more info i suggest you to check the two help links given below:---Click the link below:----How to replace Leak detection pump solenoid circuit?
http://repairhelpcenter.blogspot.in/2012/05/leak-detection-pump-solenoid-circuit.html
-----------------P1495 Leak Detection Pump Solenoid Circuit?
http://howtobyme.blogspot.in/2012/05/p1495-leak-detection-pump-solenoid.html

-----------------
This will help.
Thanks.

May 31, 2012 | Chrysler Cars & Trucks

1 Answer

Engine light stays on code p1494


P1494 code is a leak detection pump switch or mechanical fault, leak detection pump switch does not respond to input. The leak detection pump (if equipped) is located under the air filter housing on models through 2001. Check if the vapor and vacuum lines are securely connected to the leak detection pump or a diagonstic trouble code my be set like this. The leak detection pump switch may be bad and need replaced.

Sep 27, 2011 | 2000 Jeep Cherokee

1 Answer

How do i replace the natural vacuum leak detection pump on a 2005 dodge dakota?


Vehicles equipped with NGC engine control modules use an NVLD pump and system. Vehicles equipped with JTEC engine control modules use a leak detection pump. Refer to Leak Detection Pump (LDP) for additional information.
The Natural Vacuum Leak Detection (NVLD) system is the next generation evaporative leak detection system that will first be used on vehicles equipped with the Next Generation Controller (NGC). This new system replaces the leak detection pump as the method of evaporative system leak detection. This is to detect a leak equivalent to a 0.020 (0.5 mm) hole. This system has the capability to detect holes of this size very dependably.


Removal & Installation
  1. Raise and support vehicle.
  2. Remove left-rear tire.
  3. Remove plastic shield (4) in front of left-rear tire. Access to both the EVAP canister (1) and NVLD pump (6) is from the area in front of the removed tire.
  4. Disconnect electrical connector at NVLD pump.
  5. Remove vapor line at NVLD pump. Pry outward on tab (3) and rotate pump (6) clockwise about 70 for removal.
  6. Remove NVLD pump O-ring (5) from EVAP canister (1).
To Install:
  1. Install new NVLD pump O-ring (5) to EVAP canister (1).
  2. Position NVLD pump (6) into EVAP canister (1).
  3. Rotate pump (6) until tab aligns with notch in EVAP canister (1).
  4. Carefully install vapor/vacuum lines to NVLD pump.
    WARNING The vapor/vacuum lines and hoses must be firmly connected. Check the vapor/vacuum lines at the NVLD pump, filter and EVAP canister purge solenoid for damage or leaks. If a leak is present, a Diagnostic Trouble Code (DTC) may be set.
  5. Connect electrical connector to pump.
  6. Install plastic shield in front of left-rear tire.
  7. Install left-rear tire.

    2e35911.jpg
    Fig.


    aa300e1.jpg
    Fig.

Have a nice day (remember rated this help).


Mar 05, 2010 | 2004 Dodge Dakota

1 Answer

Evaporative Emission System codes


check ur gas cap for tight and proper seal that is the most common problem for the the evap codes if cap is good check fuel and vent lines for damage or leaks from gas cap under vehicle up to engine compartment

Oct 18, 2009 | 2006 Mazda 3

1 Answer

Check engine code P1494???manufacture control auxiliary emission control


Definition of error code
Evap leak detection pump pressure switch condition
Explanation


ECM detected the leak detection pump switch did change after solenoid was energized


Probable Cause
1.-Leak detection pump defective
2.-Open or shorted circuit condition
3. Solenoid defective

Oct 07, 2009 | 2003 Jeep Grand Cherokee

1 Answer

NEED TO FIX THE LEAK DETECTION PUMP ON A 1999 JEEP GRAND CHEROKEE


it may not be the leak detection pump..what codes did it show...a cracked hose going to the pump..the purge solenoid or the fuel pump can cause a leak

Nov 13, 2008 | 1999 Jeep Grand Cherokee

1 Answer

I have a check engine light on


code p2404 is from a none volvo tester it would convert over to volvo code ecm 432a ,leak diag. pump failure,now dont play with it driving should be ok but you should take it to the dealer or a volvo only shop and read codes and fix it when your ready

Aug 16, 2008 | 2004 Volvo S60

Not finding what you are looking for?
2003 Mazda MX-5 Miata Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...