Question about 2004 Mitsubishi Lancer

2 Answers

When to change clutch plate of lancer2004. i mean after how many km

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Have seen them go 200,000 mi. Depends on how you drive. Usually not untill you can no longer put it in gear or it is slipping.

Posted on Sep 15, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

If you are a good clutch driver and carefully use it only to shift, it could easily go 250,000 km. If you hold the car in place on a hill using the clutch instead of the brake , expect to get maybe 60,000 km. Your driving technique (hot rodding versus gas miser) will dictate how long the clutch plate will last.

Posted on Sep 15, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The clutchpedal seems to work but does not engage and the fluid level reamains full

It is still a bit unclear what is going on here, when you say it seems to work, do you mean the clutch disengages? Can you change gears OK with the engine running and the clutch depressed?

When you say it does not engage the plate, do you mean the vehicle does not move? To change gears it must DISengage the plate, not the other way round.

Sorry if I seem picky, but I'm trying to get it all straight. If you can change gears OK with the engine running and the clutch depressed, but the vehicle does not move when you let the clutch pedal up, then the clutch is possibly worn out and needs replacing.

If the opposite and you cannot get it into gear with the clutch depressed, then the clutch throwout fork has possibly broken, which is not uncommon. Alternatively but less likely is that there is so much air in the clutch hydraulic line that it has become ineffective.

Apr 06, 2016 | 1990 Ford F150

2 Answers

Truck clutch was replaced at only 27329 km and had to be replaced again at 29742.Not the same driver, what could be reasons for this failure?

When the clutch was replaced was the slave cylinder also replaced? How about the throw out bearing? These are the first things I'd be looking at. When you have premature failure of these components, it comes down to the person(s) driving the vehicle or the components, in this case 2 clutches in a short amount of time plus 2 different drivers = component failure. Slave cylinder not pushing / pulling the throw out bearing enough or the bearing may be hanging on the input shaft, did you reface the flywheel or put a new one in?

Mar 14, 2016 | Cars & Trucks

1 Answer

Mazda 2 has 105k miles. Why do I notice less acceleration and more RPM change?

If you accelerate especially when using high gears such as the 4th and 5th gear and the RPM is able to increase freely with the speed struggling to catch up with the RPM, it means your clutch is worn out and is slipping.

You need to get the clutch replaced in order for this issue to be rectified, especially if your clutch have not been changed before.

Nov 24, 2015 | Mazda Cars & Trucks

1 Answer

Why can't I put car in first or second after I changed the clutch it is 96 ford escort 5 speed manual transmission

it is very possible that the clutch plate is in the wrong way round and the clutch hub is hitting on the flywheel bolts

means a box out again and the pressure plate off to change the clutch plate around

Sep 13, 2015 | Ford Cars & Trucks

1 Answer

Want to know where vin plate is located mitsubishi lancer2004

by law, the VIN should be visible when you look at the left lower windshield of the vehicle, normally fixed to the inst. panel. You can also find it printed on the certification label you find on the door latch area of the drivers door when opened.

Nov 22, 2014 | 2004 Mitsubishi Lancer

2 Answers

Freelander clutch

check out the operation of the clutch system .IT is difficult to rationalise a hydraulic clutch because if it is slipping that means that the pressure plate is being held off and not fully engaging but it also means that when pressing on the clutch the there would be no problem changing gears . But if you have a cable clutch operation then it is possible that the cable is jamming inside the outer cover and holding the pressure plate off ( slipping) and gear problems. If it is cable then replace the cable first. If hydraulic then it may mean box out for a new clutch kit.

Jan 12, 2014 | Cars & Trucks

1 Answer

I have a continious noice when the engine is running. The noice is away as soos as I put my foot on the clutch. People told me that I have to put in a clutch kit. Car has 95000 Km. Toyota Corolla Advance...

the noise you hear is the thro-out-bearing .when you apply the clutch pedal it applies pressure on the pressure plate .the noise stops until you let out the clutch again,the bearing can be replaced without replacing the whole kit,clutch ,pressure plate,thro-out-bearing if money is a issue,...Merry Christmas.

Dec 03, 2013 | Cars & Trucks

1 Answer


If you mean that the clutch will slip when under load, then it's the pressure plate that's bad. It's a common Toyota problem. It's worth it to change the entire set-up { pressure plate, clutch disk, and throw-out bearing ] as the labor costs will be the same, and a clutch package is less then a pressure plate alone.

Mar 05, 2011 | 1985 Toyota Pickup

1 Answer

91 Nissan Terrano TD 2.7 engine is running fine but loses power at transmission can not go above 10 km per hour

between engine and transmission has what we call clutch. it will not work well if it has broken or sliding clutch. check pressure plate,clutch disc and release bearing.

Dec 29, 2010 | 2003 Nissan Pathfinder

2 Answers

Clutch snatching

i think it is normal every clutch on each car feels different if it is not slipping i would not worry about it THE CLUTCH IS IN GOOD CONDITION

Dec 12, 2008 | 1991 Volkswagen Corrado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides