Question about 1999 Chevrolet K1500

Open Question

Need to replace speakers in 2001 chevy silverado extended cab

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
280zlvr
  • 126 Answers

SOURCE: cab corner extended cab 99 silverado LH

there is a new style body panel adhesive that makes this job very easy for the home body man this panel needs to be prefit by you make shure it lines up and looks strait then apply the glue on the eges and drive a couple of self tapping screws into it to hold it until the glue dries usually 1 24 hr period after the glue is hard then remove the screws and sand off excess glue and fill the screww holes with spot and glaze putty sand all areas to prepare for next step which is feathering with fibermix and then spot putty prime and paint see the heat from a welding machine is nice to but it warps the panel being put on the glue lasts for years and it doesnt warp panels thanks for using a great resource like fixya

Posted on Jul 13, 2008

Ad
  • 14036 Answers

SOURCE: Replace window motor assembly 2001 Chev 1500 extended cab truck

you can order it at some dealer ships . it cost about 150.00 dollars or more.

Posted on Apr 02, 2009

  • 3600 Answers

SOURCE: how do i change my upper and lower ball joints

Jack up the car remove wheel remove brake caliper and remove rotor rent a ball joint press remover and installer tool (at schucks you get money back when you bring it back) if it's 4 wheel drive you will have to remove the axle shaft next pull the snap ring off on the top side and put tool on the lower tie rod end and press out, next do the top press out top joint next sand ball joint sockets so it is clean lube with WD-40 next press in top ball joint and then lower ball joint. In this order otherwise you will have to un install the top ball joint by removing the pin then nut.

Posted on Aug 19, 2009

BeninVa
  • 389 Answers

SOURCE: Needing to replace the power steering pump on a

Disconnect the negative cable from the battery,(WARNING if you have the TheftLock Radio, make the system is off before doing anything that requires the battery to be disconnected)
Remove the radiator upper fan shroud,
Remove the serpentine belt,
Place a drain pan under the hoses to catch the fluid and remove the and remove the hoses from the hard lines coming out of the pump, making a note of which is which, stuff the end of a clean rag into each hose to prevent anything from getting inside it,
Using a pulley removal tool, remove the pulley from the pump,
Remove the four bolts from the rear of the pump( V8 has 4 bolts,V6 has 2 bolts ) and lift the pump out.
Installation,
Place the pump in it's mounting bracket and install the bolts, tighten them to 37 ft lbs.
Connect the hoses and tighten securely,
Press the pulley on the shaft using a pulley installation tool,DO NOT HAMMER IT ON,, the proper position is the front of the hub flush with the end of the shaft,
Install the serpentine belt,
Install the upper fan shroud,
Fill to the cold mark the correct of NEW fluid,
Re-connect the battery cable.
Bleed the system as follows,
Wheels straight ahead,
Start the engine and allow it to fast idle,
Check for leaks,
Re-check the fluid lever and add more if needed to keep it up to the Cold mark,
Move the steering wheel from side to side several times WITHOUT hitting the stops, this will work the air out of the system, keep adding fluid if needed during this process,
When the fluid level stops going down the system should be free of any trapped air,
Set the wheels straight ahead again and allow the engine to run for 5-10 minutes before shutting it down, re-check the fluid level,
Road test the vehicle and drive it long enough to get it up to normal operating temperature,
Re-check fluid level and fill it to the Hot level.







Posted on Dec 31, 2009

  • 540 Answers

SOURCE: do i need to pull my dash to replace my heater

yes

Posted on Jan 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 chevy silverado 1500 extended cab has a electrical problem


Lets start at the beginning.
What resets itself, and what is the issue with the headlights ?

Aug 01, 2012 | 2002 Chevrolet Silverado 1500

1 Answer

I just need a replacement rear end for my son's 2001 1/2 ton chevy ext cab silverado! Can you direct me to someone who can sell me one without taking me for a cleaning?


i would call around to different wrecking yards to see who has one and how much for it,they may want the one you removed back as a core charge or some thing.

Apr 12, 2011 | 2001 Chevrolet Silverado

1 Answer

My 2001 chevy 4x4 extended cab heater switch has stoped working on #5 setting, 1 year later it worked on # 4 setting this morning it only works on # 3 setting 2 and 1. Would you please let me know what I...


SOUNDS LIKE THE SWITCH & OR THE BLOWER MOTOR RESISTOR, ARE THE PROBLEM WITH THE LOWER SPEEDS. SPEED 5 MAY HAVE ITS OWN FUSE, REFER TO OWNERS MANUAL FOR INFORMATION ABOUT THE HEATER/AC FUSE.

Jan 10, 2011 | 2001 Chevrolet Silverado 1500

1 Answer

Heater is blowing cold air. I have a chevy 2001 silverado extended cab, long wheel base. what could cause this?


My truck had the same issue and from I have read, it is pretty common. I just felt the heater hoses under the hood. If there is one hot and one cold, with the engine running and the heater set to maximum, rapidly squeeze and release the hot hose for about fifteen seconds.I just did this to my truck and it "Burped" the heater core. I got instant LAVA HOT air!! I hope this helps.

Dec 02, 2010 | 2001 Chevrolet Silverado

2 Answers

Do i need to pull my dash to replace my heater core in a 2001 chevy silverado ext cab


You will need to pull the dash and a bunch of other components in order to access the heater core. Getting ready to do the same repair and really not looking forward to it.

Jan 07, 2010 | 2001 Chevrolet Silverado

2 Answers

2000 Chevy Z-71 A/C problems


maybe drop the blower motor and check the vents for obstructions. I worked on a friend's car this spring that had a two year-old repair bill sucked in to the blower wheel....it limited the air output but made a lots of noise in the process.

Jun 24, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Replace window motor assembly 2001 Chev 1500 extended cab truck


you can order it at some dealer ships . it cost about 150.00 dollars or more.

Jan 12, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Need to replace my speakers


if this is a ext cab the doors are 4x6, and front are 6 1/2

Jan 07, 2009 | 2002 Chevrolet Silverado

Not finding what you are looking for?
1999 Chevrolet K1500 Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...