Question about 1993 Acura Legend

1 Answer

1993 Acura Legend 4 door. Why doesn't my rear windows work? The motors and regulators do work when connected straight to the battery.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 3,640 Answers

If the windows work when hooking to battery, then check the switches and wiring. it may even be a bad ground. I worked on power window a few months ago, and it had a bad ground as not to work. try by running a wire from motor or ground connection to a bare spot on door. if the window works then you can either put in a screw or ground to something on door.

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT CAR WILL INERCHANGE WITH 94 GEO METRO FOR SPARE TIRE


These are the same bolt patterns, bolt pattern is 4 X 4.5 or also known as 4 X 114MM. Measure 2 lugholes across from each other and it should measure 4 1/2" US or 114MM. the center hubs may be smaller/larger. Check the center hub size before purchasing:
1997 Acura- CL 16 x 6 (5 straight spokes)
1998 Acura- CL 16 x 6 (5 dual straight spokes)
1998 Acura- CL 16 x 6 (7 straight spokes
1990-89 Acura- Legend 15 x 5.5
1996-95 Acura- TL 15 x 6 (5 straight spokes with groove)
1997-98 Acura- TL 15 x 6 (11 straight spokes)
1994-92 Acura- Vigor 15 x 6 (11 triangular slots)
1999-98 Chevrolet- Metro
1989-85 Chevrolet- Sprint
1991 Dodge- Colt Vista 13 x 5 (15 slots)
1993-92 Dodge- Colt Vista 14 x 5.5 (5 straight spokes)
1992-84 Eagle- Summit/Summit Wagon
1992-91 Eagle- Summit 13 x 5 (15 slots)
1993-88 Ford- Festiva 12 x 4 40mm offset
1993-91 Ford- Festiva 12 x 4.5 40mm offset (8 elongated triangle slots)
1997-89 Geo- Metro
1999-92 Honda- Prelude
1999-90 Honda- Accord (4 cylinder models)
1999-91 Hyundai- Elantra
1995-92 Hyundai- Elantra 14 x 6 (16 slots)
1995-92 Hyundai- Elantra 14 x 5.5 (7 curved spokes)
1998-96 Hyundai- Elantra 14 x 5.5 (5 straight spokes)
1999-90 Hyundai- Accent/Excel/Pony
1994-92 Hyundai- Excel 13 x 5
1991 Hyundai- Sonata 15 x 6 (18 rectangular slots)
1994-92 Hyundai- Sonata 15 x 6 (9 triangular slots)
1996-95 Hyundai- Sonata 15 x 6 (9 straight spokes)
1997-95 Hyundai- Sonata 15 x 6 (5 twisted spokes)
1998-97 Hyundai- Sonata 15 x 6 (5 straight single groove spokes)
1995-90 Hyundai- Scoupe
1992-91 Hyundai- Scoupe 14 x 5 (6 curved spokes)
1995-93 Hyundai- Scoupe 14 x 5 (5 curved spokes)
1998-97 Hyundai- Tiburon 15 x 6 (5 twisted spokes)
1998-97 Hyundai- Tiburon 15 x 6 (5 raised straight spokes)
1989-81 Mazda- 323/GLC
1985-84 Mazda- RX7 GSL-SE 14 x 5.5 40mm offset
1991-86 Mazda- RX7 14 x 5.5 40mm offset
1987-85 Mazda- 626/MX-6
1994-91 Mercury- Capri 14 x 5.5 45mm offset (16 holes)
1994-91 Mercury- Capri 15 x 6 45mm offset (3 curved spokes
1994-91 Mercury- Topaz 14 x 5.5 (16 holes)
1998-92 Mitsubishi- Expo/Expo LRV/Vista Wagon
1994-92 Mitsubishi- Expo 14 x 5.5 (5 straight spokes)
1999-84 Mitsubishi- Galant
1991 Mitsubishi- Galant 14 x 5.5 (18 slots)
1991 Mitsubishi- Galant 15 x 6 (8 straight spokes)
1991 Mitsubishi- Galant 15 x 6 (5 straight spokes)
1993-91 Mitsubishi- Galant 14 x 5.5 (15 slanted spokes)
1992 Mitsubishi- Galant 15 x 6 (5 straight spokes)
1993 Mitsubishi- Galant 15 x 6 (8 triangular and 8 rectangular slots)
1993-84 Mitsubishi- Mirage
1993-91 Mitsubishi- 2000GTX 14 x 5.5 (18 slots)
1991-80 Mitsubishi- Tredia
1999-93 Nissan- Altima
1995-82 Nissan- Stanza
1991-84 Nissan- Maxima
1990-78 Nissan- B310/Pulsar
1989-94 Nissan 240sx
1989-94 Nissan Silvia
1986-82 Nissan- Sentra
1993-84 Plymouth- Colt
1985-79 Plymouth- Arrow/Champ
1999-89 Suzuki- Swift
1991-80 Toyota- Cressida
1985-80 Toyota- Celica

Oct 30, 2017 | Geo Cars & Trucks

1 Answer

Power windows on automobile


Hey. This is very likely power window switch and second one would be a relay. Look in ovners manual which relay is responsible for your windows and or doors. Let me know if you can't check it out

Mar 14, 2017 | 1990 Acura Legend

1 Answer

Acura legend keys in trunk


hi.
try this link out might help to find out how to get it sorted.
1992 Acura Legend Locked my keys in the trunk Google Search

Nov 01, 2017 | 1992 Acura Legend

1 Answer

I a looking for instructions on how to install a power window regulator into a 98 Acura CL


Door Glass and Regulator - REMOVAL & INSTALLATION
  1. Remove the door panel.
  2. Remove the plastic cover from the door frame.
  3. Remove the power window switch from the door panel.
  4. Connect the power window switch to the door harness.
  5. Fully lower the glass.
  6. Pull the channel guide cover off.
  7. Remove the screws from the channel guide.
  8. Remove the center channel guide (if equipped).
  9. Carefully remove the glass until you can see the bolts and then carefully loosen all of them.
  10. Slide the window track guide to the rear.
Before removing the guide pin, scribe a line around it. This will enable you to install it in the exact position it was removed in.
  1. Remove the glass by gently lifting it from the guide.
  2. The glass can now be removed by pulling it through the window slot.
CAUTION Use extreme caution when handling window glass.
Check the guide pin for wear. Replace as necessary.
  1. Detach the connector and remove the regulator through the hole in the door.
Scribe a line around the rear roller guide bolt. This mark will show where the original adjustment was at before you removed the component.
  1. Remove the power window motor from the window regulator assembly.
  2. Remove any clips and pull the glass run channel out.
It may be necessary to remove the glass stopper.

WARNING Grease all of the sliding surfaces of the regulator or component failure may occur.
To install:
  1. Install the window motor on the regulator assembly.
As a check, you can connect a known good 12 volt power source to the window motor to check the operation of the entire assembly. The regulator should operate with a steady, consistent motion in either direction.
  1. Install the glass run channel into the door as shown.
  2. Install the regulator.
  3. Install the glass.
  4. Install the center channel guide.
  5. Move the glass up and down to ensure free movement.
  6. Attach the door wiring harness to the door.
  7. Disconnect the window switch (on power controlled models) and install it into the door panel.
  8. The remainder of the installation process is the reverse of removal.


Electric Window Motor - REMOVAL & INSTALLATION
  1. Remove the regulator from the door assembly. Refer to the procedure in this section.
  2. Except for the rear doors, drill a hole through the regulator sector gear and backplate. Install the bolt and nut to lock the sector gear in position. Be careful not to drill a hole closer than 7 / 16 in. (11mm) from the edge of the sector. Also, do not drill through the lift arm attaching portion of the sector gear, or the joint integrity will be jeopardized.
  3. Drill out the ends of the motor attaching rivets using a 1 / 4 in. (6mm) bit.
  4. Remove the motor and the remaining portions of the rivets from the regulator. Except for the rear doors, one rivet will not be accessible until assembly.
(see Figures 1 and 2 / click over pic for zoom)


zjlimited_251.jpg


Fig. 1: Regulator and motor assembly-except rear doors

zjlimited_252.jpg

Fig. 2: Secure the rivets by collapsing the rivet ends using a ball peen hammer



To install:

  1. Position the new motor to the regulator. With the aid of an assistant, install new rivets by collapsing or crushing the rivet ends using a ball peen hammer.
  2. Except for the rear doors, once two of the three rivets have been installed, remove the bolt securing the sector gear to the backplate, then use an appropriate electrical source (such as the vehicle's window motor harness) to rotate the regulator, providing access to the remaining rivet.
  3. Except for the rear doors, use a flat nosed rotary file to grind off one sector gear tooth from the side which does not contact the driven gear. This is necessary to reach the remaining rivet. Remove the old rivet, then install the remaining new rivet.
  4. Install the regulator to the door assembly.


Hope this helps (remmeber to rate and comment this).

Dec 16, 2010 | Acura CL Cars & Trucks

1 Answer

Acura legend wont start


Run hot wire from battery to coil to see lf that is your problem.

Jan 11, 2010 | 1993 Acura Legend

1 Answer

Connect (-) power up cable to my four windows acura legend 1192


havent a clue to be truthful,does the kit come with a wiring diagram ,i should imagine that their is a central block with 4 outlets ,one for each window that connects to teh earth side of the window winder motor.if you have a diagram with instructions then i could tell you more sorry

Oct 24, 2009 | 1992 Acura Legend

1 Answer

My 93 acura legend wont start. Ticking sound??


That sounds like a dead battery. The ticking sound is the relay (a type of switch) which enables power to the starter motor when you turn the key. If the battery is weak, the relay will click, but there is not enough power to turn the starter motor.

Oct 07, 2009 | 1993 Acura Legend

1 Answer

ACURA LEGEND WINDOW WON'T ROLL DOWN, OTHERS WORK FINE


Driver windows tend to work more due to its on the driver side and tend to fail before others. New window switch is fairly cheap, the motor I would get it from a junk yard or you can get both from a junk yard. check all fuse and relay first. test the switch or replace it before you start tearing the door cover off. working and replacing the door motor is not an easy task on the ledgend.

Aug 25, 2009 | 1992 Acura Legend

1 Answer

1992 Acura Legend


check the brushes inside the starter motor they may be jamed or worn

Apr 26, 2009 | 1992 Acura Legend

1 Answer

Acura legend passenger windows wont go down


PASSENGER MASTER SWITCH TURNED OFF ON DRIVERS DOOR WINDOW SWITCH PANEL?????

Mar 30, 2009 | 1992 Acura Legend

Not finding what you are looking for?
1993 Acura Legend Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...