Question about 2000 Oldsmobile Alero

1 Answer

2000 Alero I just had the windshield replaced and there are some trim or molding pieces on both sides of the windshield and I don't know what they are called so I can replace the broken one.

Posted by on

  • Anonymous Mar 31, 2014

    6 inches of the windshield trim is broke how do I take it off without destroying it?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Expert
  • 611 Answers

Cowl go to gmpartsdirect.com and you can see the exact part you need

Posted on Jun 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many airbag sensors in a 2008 gmc acadia


1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

Aug 12, 2015 | GMC Cars & Trucks

2 Answers

How to install replacement sunroof motor on a 1999 Pontiac grand prix


Important: This sunroof system is timed from the factory in order to allow the actuator to shut off automatically when the sunroof window reaches a certain position. Use extreme care when removing the actuator from the sunroof module. This may cause the timing to be thrown off. This may damage to the sunroof. Anytime the actuator needs to be removed from the module, ensure that the sunroof window is in the fully closed position.
Remove the sunroof window. Refer to Sunroof Glass Panel Replacement .
Slide the sunshade fully rearward. Move the sunroof window to the vent position. Remove the sunroof screws (two on each side). Remove the sunroof window from the module.
Place the sunroof module in the fully closed position. Remove the headliner. Refer to Headlining Trim Panel Replacement in Interior trim.
Tools Required ?€¢
J 38778 Door Trim Pad and Garnish Clip Remover


?€¢
J 2772-C Headliner Installer

  1. Remove the sunshades. Refer to Sunshade Replacement .
  2. Remove the overhead console, if equipped. Refer to Roof Console Replacement .
  3. Remove the sunshade retainers. Refer to Sunshade Anchor Replacement .
  4. Remove the power sunroof switch, if equipped. Refer to Sunroof Switch Replacement in Roof.
  5. Remove the sunroof trim lace, if equipped. Refer to Sunroof Seal/Molding Replacement in Roof.
  6. Remove the dome light, if equipped.
  7. Remove the coat hooks. Refer to Coat Hook Replacement .
  8. Remove the assist handles. Assist Strap Replacement
  9. Remove the rail lamp. Refer to Roof Side Rail Lamp Replacement in Lighting.
  10. Remove the windshield side garnish molding. Refer to Windshield Pillar Garnish Molding Replacement .
  11. Remove the upper quarter trim panels. Refer to Rear Quarter Upper Trim Panel Replacement .
  12. Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement .
  13. Pull down on the door opening weatherstrip seal on both the front and the rear doors.
  14. Remove the 2 rear retainers (2) using J 38778 Door Trim Pad and Garnish Clip Remover. Disconnect the headliner electric harness at the right side of the rear window shelf. Rotate the right front seatback to a horizontal position. Remove the headliner from the vehicle through the right front door.
Disconnect the electrical connector from the actuator.
Important: Before removing the actuator, ensure that the pins J 41718 are tight and holding the cable.
Thread the J 41718 into the front sunroof window screw hole in order to retain the cable adjustment. Remove the sunroof actuator screws. Remove the sunroof actuator from the module. Did you look for a video on youtube ?

Feb 27, 2015 | 1999 Pontiac Grand Prix

2 Answers

Water Leak


my suggetion is if the windsheild was replaced the water is getting under the molding through the top or top side of windshield and traveling down the channel under the molding to get into ur car one way to check this is take real soapy water and just pour it along the the top annd side of windsheild on side that is leaking .. see if that is the substance getting in .....

Jan 02, 2012 | 2006 Chevrolet Impala

3 Answers

Vibrating noise from the dash at higher speeds


I've experienced a rapid frequency vbibration that sounds like it comes from the front left dash. I isolated it as the small plastic molding on the outside of the windshield, just below the windshield. There is a small plastic strip like molding piece that ends near the end of the windshield. I used some double sided foam tape sandwiched between the bottom of the molding and the plastic piece belwo it and that solved the problem. I have had to replace the tape every year or so

Feb 01, 2010 | 2000 Mercury Grand Marquis

1 Answer

The rubber mold that fits between the windshield and the right exterior body (that runs from the top of the van to the bottom of the windshield)is loose. It is attached at the top and the bottom but wants...


Window trim molding is tricky. They use a combination of adhesives and clips to hold it in place. Go to a parts counter for a dealer and have them look it up and it will say if it is glued or clipped.

Oct 22, 2017 | 2000 Toyota Sienna

1 Answer

I have horrible noise coming from the windshield of my 01 Explorer. I had the windshield replaced about a year ago and never noticed the noise while driving in the city; now I'm commuting on the freeway...


What I would do is look around the edges of the windshield where the molding trim runs along for an open gap. The molding trim should be flat against the windshield as possible. A open gap would cause a whistle type of noise during high speeds. An automotive supply store should carry a glue for hold the trim piece back down on to the windshield.

Sep 06, 2009 | 2001 Ford Explorer

1 Answer

How do I replace the cabin air filter on a 1997 mercury sable?


It is underneath the black plastic pieces under/below the wipers. There are just a few round fasteners that hold down the passenger side piece that need to be removed to access the filter.
You have to remove the windshield wiper arms, then take off the plastic molding that lies between your windshield. Once that is off (it comes out in two pieces) on the passenger side of the car, under the windshield just behind the firewall there is a plastic rain shield with two screws. Remove the rain shield. The cabin filter is under that rain shield. FYI...every bolt is metric, and be careful when removing the plastic molding-only turn those screws a half turn, they break very easily!

Jun 25, 2009 | 1997 Mercury Sable

2 Answers

Door panel


this link is for a Grand Am but the door panels are very close and it should work.
http://www.a1electric.com/install/grand/grandam-2.htm

May 14, 2009 | 2000 Oldsmobile Alero

1 Answer

Where do i find the black cover or trim for my windshield


Any Auto Parts Store or Automotive Glass Shop will have what you Need.

Jan 01, 2009 | 2003 Oldsmobile Alero

1 Answer

Headlights. sensor


You could replace the sensor or try disconnecting the DRL control module .What relay was replaced ? I see no relay on wiring diagrams or in service info. Replacing the Daytime Running Lamp (DRL) Ambient Light Sensor isn't hard . Just take the top dash pad off ,easy .
Removal Procedure
Remove the instrument panel (IP) upper trim. Refer to Instrument Panel Upper Trim Pad Replacement in Instrument Panel, Gages and Console.
Remove the security system LED. Refer to LED Indicator Replacement - Vehicle Security System in Theft Deterrent.
Twist the DRL sensor counterclockwise in order to remove the sensor from the IP upper trim.
Remove the DRL sensor from the wiring harness.

Removal Procedure
Remove the windshield garnish molding. Refer to Windshield Pillar Garnish Molding Replacement in Interior Trim.
Important: Remove the upper trim panel slowly, the retainer clips could possibly fall into the instrument panel.
Lift the instrument panel (IP) upper trim panel approximately 51 mm (2 in) and pull rearward to release the retainers.
Remove the DRL ambient light sensor. Refer to Daytime Running Lamp (DRL) Ambient Light Sensor Replacement in Lighting Systems.
If equipped, remove the sun load sensor.

Pull the windshield garnish molding from the A-pillar in order to disengage the retaining tabs and clips.
Remove the windshield garnish molding from the A-pillar.

Daytime Running Lamps (DRL) Control Module
Left side of the IP

Removal Procedure
Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Remove the instrument panel insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side in Instrument Panel, Gages and Console.
Slide the daytime running lamp module from the bracket.
Disconnect the electrical connectors.

Oct 24, 2017 | 2002 Chevrolet Venture Passanger

Not finding what you are looking for?
2000 Oldsmobile Alero Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...