Question about Chevrolet Blazer

1 Answer

2000 s10 blazer turn left signal on and hazard lights come on have replaced everything on it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,374 Answers

Either you have a short to ground in the flasher unit or if you haven't done this already you may want to try it. Replace all bulbs WITH DEALER BU LBS. Cost a little more but it has sovled similar problems.

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals don't Flash signal, the fuse is fine and all four lights light up. Also the Hazard light switch will not depress which could be the whole problem. What think? 2000 Pontiac Grand Prix GTP


This vintage era GM vehicle is known for turn signal issues due to bad hazard switches. Replace the hazard switch and everything should return to normal

Sep 04, 2017 | Pontiac Cars & Trucks

2 Answers

My left brake light/turn signal isn't working! I replaced the bulbs and turn signal flasher! Still not working! Its 2000 Chevy s10 blazer


If the other brake and turn lights are working the brake light and flasher units are ok . With a test light check at the bulb holder terminal and bulb holder body, test light should glow ,if not check from terminal to a metal part of panel away from the light body . If test light now glows the brake light body has a bad earth if the test still not glowing the power cable to the light is broken.

May 20, 2014 | Cars & Trucks

1 Answer

Hi i have a 2001 s10 the 3 rd brake light is working but the side brake light arent - side lights come on checked fuses heeeelllpp


Found this problem on a few Blazers and S-10s . Try pushing the hazard button in and out a dozen or so times then turn them off and check brake lights. The brake light circuit runs though the turn signal switch and hazard switch. Contacts get dirty and wont let power get through. Hope it works for you!

Dec 04, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

Problem with my 97 Chevrolet S10 Blazer


I'd look into the multifunction switch. That controles both hazard and turn.

Dec 12, 2009 | 1997 Chevrolet Blazer

1 Answer

Where is the turn signal relay on a chevy s10


On 95-97 and 1998, both the turn signal and hazard flashers are located behind the lower dashboard trim just to the left of the cigarette lighter. You can not get to it without taking apart the trim (stupid design). Or you have to drill a 2" diameter hole in the trim with a velcro cover so you would never have to do it again1999 and later it is under the glove compartment
to disassemble it without drilling
It's behind the panel to the left of the cigarrette lighter. You need a Torx 25 screwdriver and another screwdriver for those hex shaped screws, forgot the size. First unscrew the 2 Torx 25 screws beneath the steering wheel. Then unscrew the rest of those Hex screws on the bottom. The panels overlap, so be prepared for a lot of unscrewing. You do need to unscrew the middle black panel on the bottom, right beneath the cig lighter. It's held by two Hex shaped screws, one on each side and are hard to unscrew. Also you need to remove your spare change sliding tray to unscrew the last hex looking screw. Once you pop your panel off, the turn signal flasher is the right one. The Hazard flasher is the left one. You can find a replacement part at Autozone, and DON'T get the $184 Flasher switch, all you need is the signal flasher. It's shaped like a cylinder with TWO prongs on it.

Nov 03, 2009 | 1994 Chevrolet S-10 Blazer

3 Answers

Turn signal relay switch, 94 s10 chevy blazer


The Turn signal relay on a 94 s10 blazer is located under the cluster area right behind the panel that holds the parking brake release handle you will see it once a couple of trim panels get remove it will be to the right side of the brake release handle

Nov 18, 2008 | 1994 Chevrolet S-10 Blazer

2 Answers

Turn Signal Flasher


58940048Its behind the center of the dash under the Ashtray U need TORX screwdrivers to take out the screws got to take off nearly all over the under dash plastic trim.
Contact me if you need more help Thanks

Jul 31, 2008 | 1996 Chevrolet Blazer

3 Answers

2000 gmc jimmy brake lights


I had the same problem with my 2001. I found it was the multi function switch. Better known as your turn signal switch. I found that the hazard switch portion of it had shorted. replacement is fairly easy, aftermarket part is available, much cheaper than GM.

Jul 15, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...