Question about Chevrolet Corsica

1 Answer

Which brake line from the brake fluid reservoir goes to the left rear brake?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 112 Answers

Not knowing exactly what year & model makes this a question that really cant be answered correctly.
Some car years have drum brakes in the rear & some have disk, some have a single line from the master the goes to the front & rear & each "T"'s off in the middle letting equal pressure to each. Some have an individual line right from the master cylinder to each wheel. There are even systems called X systems that apply pressure in an "X" configuration (L front-rear RT / RT front.-rear L ) To get a more accurate answer, the make model & year should be listed as well if it has 4 wheel disk or not.

HERE IS SOME HELP

http://www.ehow.com/articles_3236-auto-brakes.html

Posted on Sep 15, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 villager right front and left rear brake seizes after driving a couple of miles wont release until line is loosed


Did you by chance add power steering fluid to the brake reservoir instead of brake fluid?

Mar 01, 2015 | 1995 Mercury Villager

1 Answer

Where is the clutch fluid reservoir on a 2006 toyota corolla


The brakes and clutch share the brake master cylinder reservoir,and a line from clutch master cylinder goes to the brake reservoir and it takes brake fluid,dot 3 type.

Jan 19, 2014 | 2006 Toyota Corolla

1 Answer

Brakes not working


The front portion of the reservoir has fluid used for the front brakes which provide the majority of the vehicles stopping power. There is a valve that is supposed to shift to isolate the front and rear brakes when this occurs but it doesn't always work as designed. You have lost all the fluid in the front brake system. This is due one of these possible issues:

Broken brake line
Broken brake hose from line to caliper
Leaking caliper seal

You need to find and repair the leak, refill and bleed the front brake system to get the vehicle back in service. IT IS NOT SAFE TO DRIVE IN ITS CURRENT STATE!!!

Dec 06, 2013 | 1993 Jeep Grand Cherokee

2 Answers

1999 buick century brake pedal goes to floor-put new master cylinder on and blead both brake lines and master cylinder and pedal still goes to floor


Sounds like you may have a hydraulic leak somewhere. Check the rear wheel cylinders and front brake hoses going to the calipers.

Jan 26, 2012 | 1999 Buick Century

2 Answers

I have a 2004 Land cruiser and changed the right rear brake cyl and brake shoes . What is the proper procedure to bleed the rear brake system. Thank you for your help.


  1. Check the fluid level in the reservoir after bleeding each wheel. Add DOT3 fluid, if necessary.
  2. If the master cylinder was disassembled or if the reservoir becomes empty, bleed the air from the master cylinder as follows:
    1. Disconnect the brake lines from the master cylinder.
    2. Slowly depress the brake pedal and hold it.
    3. Block off the outlet plug with your finger, and release the brake pedal.
    4. Repeat 3 or 4 times.

  3. Bleed the brake starting with the one furthest from the reservoir and then the next furthest, etc.
  4. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
  5. At the point when fluid stops coming out, tighten the bleeder plug to 11 Nm (8 ft. lbs.), then release the brake pedal.
  6. Repeat until all the air in the fluid has been bled out.
  7. Repeat the procedure to bleed the air out of brake line for each wheel.
  8. Check the fluid level and add DOT3 fluid if necessary.

Aug 07, 2011 | 2004 Toyota Land Cruiser

2 Answers

My brakes will not get hard. The pedal goes to the floor. I just changed rear caliper and rotor on the drivers side.


DId you bleed the system after you changed the caliper? If the Master cylinder lost it's fluid while you were changing the caliper, then there is air in the system and you need to bleed the entire system. start with the REAR RIGHT, then the REAR LEFT and then the FRONT RIGHT and last the FRONT LEFT. make sure the master cylinder NEVER runs low on fluid and DO NOT re-use any fluid that you get out of the calipers.

Dec 27, 2010 | 1992 Cadillac Seville

2 Answers

Brake pedal goes down to the floor to make it stop


check first the brake fluid reservoir to see if it is full, then bleed the brakes if the petal will not come up.

Dec 25, 2010 | 2000 Ford Taurus

1 Answer

How to bleed brakes on 2002 toyota sienna


Here is the procedure from the service manual. I would add just one thing. Do each wheel in this order

  1. right rear wheel
  2. left rear wheel
  3. right front wheel
  4. left front wheel
BLEEDING

HINT: If any work is done on the brake system or if air in the brake lines is suspected, bleed the air from the system.

NOTICE: Do not let brake fluid remain on a painted surface. Wash it off immediately.


a)FILL BRAKE RESERVOIR WITH BRAKE FLUID Fluid:SAE J1703 or FMVSS No. 116 DOT3

b)BLEED MASTER CYLINDER HINT: If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.

c)Disconnect the brake lines from the master cylinder. SST 09023-00100 Slowly depress the brake pedal and hold it.

Block off the outlet plug with your finger and release the brake pedal.
Repeat (b) and (c) 3 or 4 times.


BLEED BRAKE LINE

1. Connect the vinyl tube to the caliper or wheel cylinder bleeder plug.
2. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
3. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal. Torque: (Bleeder plug) Front brake caliper
: 8.3 Nm (85 kgf-cm, 74 inch lbs.) Rear wheel cylinder: 8.5 Nm (87 kgf-cm, 75 inch lbs.)
4. Repeat (b) and (c) until all the air in the fluid has been bled out.
5. Repeat the above procedure to bleed the air out of the brake line for each wheel.

CHECK FLUID LEVEL IN RESERVOIR Check the fluid level and add fluid if necessary. Fluid: SAE J1703 or FMVSS No. 116 DOT3

Jun 25, 2010 | 2002 Toyota Sienna

3 Answers

What order do I bleed the brakes on a 2002 toyota sequoia


ALWAYS START YOUR BLEED PROCESS AT THE WHEEL FARTHEST FROM THE MASTER CYLINDER, WHICH IN YOUR CASE IS THE RIGHT REAR, THEN THE LEFT REAR, FOLLOWED BY RIGHT FRONT AND THEN LEFT FRONT.

Oct 21, 2009 | 2002 Toyota Sequoia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...